manualshive.com logo in svg

VERDER Carbolite Gero CSR, Installation And Operation Instructions Manual

Share
Download
VERDER Carbolite Gero CSR Installation And Operation Instructions Manual Download Page 29

12.0

Decommissioning, Storage and Disposal

12.1

Decommissioning

1. Isolate the product from the power supply
2. Allow the product to cool to room temperature
3. Disconnect the product from the power supply
4. Disconnect all additional equipment and external connections

12.2

Storage (Long Term)

Store in a cool, dry place.

Note:

If the furnace is exposed to a humid environment during storage,

it must be fully dried out before recommissioning. All internal electrical
circuits should be checked for signs of moisture. If there are visible
signs of moisture, the product should be isolated from the power supply
and allowed to dry out at ambient temperature for at least 24 hours.
Please contact Carbolite Gero Service for further advice.

12.3

Disposal

Note:

This product should only be disposed of in accordance with

local regulations and requirements regarding electrical equipment.

Within the European Community the disposal of electrically operated devices is
regulated according to guidance based on the EU Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Disposal regulations may differ worldwide.

If uncertain, please contact Carbolite Gero for advice on disposal.

29

Summary of Contents for Carbolite Gero CSR

































Reviews:

No comments

Brands by name

Popular brands

Load more brands