background image

Verasys® 32 Point 24 VAC Application Controller Installation Instructions

19

Table 5:  Controller Terminal Blocks, Functions, Ratings, Requirements, and Cables (Part 1 of 4)

Terminal Block
Label

Terminal Label

Function, Ratings, Requirements

Determine Wire Size and Maximum 
Cable Length

1

Universal
(Inputs)

+15 V

15 VDC Power Source

 for active 

(3-wire) input devices connected to 
the Universal IN

n

 terminals;

provides 80 mA total current.

Note:

80mA current limit is shared 

between the BI + 15V supply and the 
UI + 15V supply.

Same as (Universal) 

INn

Note:

Use 3-wire cable for devices 

that source power from the +15V 
terminal.

COM

15 VDC Power Source

 for active 

(3-wire) input devices connected to 
the Universal IN

n

 terminals;

provides 80 mA total current.

Note:

80mA current limit is shared 

between the BI + 15V supply and the 
UI + 15V supply.

Same as (Universal) 

INn

INn

Analog Input - Voltage Mode (0–10 
VDC)

10 VDC maximum input voltage 
Internal 67k ohm pull-down

See Guideline 

A

 in Table 6.

Analog Input - Current Mode 
(4–20 mA)

Internal 100 ohm load impedance

See Guideline 

B

 in Table 6.

Analog Input - Resistive Mode 
(0–600k ohm)

Internal 12 V. 15k ohm pull-up
Qualified Sensors: 0–2k ohm 
potentiometer
RTD (1k Nickel [Johnson Controls 
sensor] 1k Platinum,  and A99B 
Silicon Temperature Sensor)
Negative Temperature Coefficient 
(NTC) Sensor (10k Type  L, 10k JCI 
Type II, 2.252k Type II)

See Guideline 

A

 in Table 6.

Binary Input - Dry Contact 
Maintained Mode

1 second minimum pulse width 
Internal 12 V. 15k ohm pull up

See Guideline A in Table 6.

ICOMn

Universal Input Common 

for all  

Universal Input terminals

Same as (Universal) 

INn

Summary of Contents for LC-VAC300 0 Series





























Reviews: