background image

SECTION

DATE

SUPERSEDES

TITLE

HT40/50KX

C150

02-21-14E

11-29-12D

DECAL DRAWING & LIST

22181C

®

VENCO VENTURO INDUSTRIES LLC

CINCINNATI, OHIO

PART NO.: 15392

DECAL:

DANGER - ELECTROCUTION HAZARD

FUNCTION: To inform the operator that the

machine (crane) represents an
electrocution hazard should it come
too near or in contact with
electrical voltage source.

QUANTITY: 1

PLACEMENT:Left side of rear cover.

PART NO.: 15391

DECAL:

DANGER - NOT PASSENGER LIFT

FUNCTION: To inform the operator not to lift,

support or transport personnel, and to ensure
that crane operator is adequately trained.

QUANTITY: 1

PLACEMENT:Left side of rear cover.

PART NO.: 15390

DECAL:

CAUTION - INSPECT VEHICLE & CRANE

FUNCTION: To inform the operator of key

operating requirements.

QUANTITY: 1

PLACEMENT:Left side of rear cover.

PART NO.: 22499

DECAL:

KNOW YOUR SIGNALS

FUNCTION: To inform the operator of

proper signals.

QUANTITY: 1

PLACEMENT:Right side of rear cover.

15390-D

!

CAUTION

1. INSPECT VEHICLE AND CRANE INCLUDING

OPERATION, PRIOR TO USE DAILY.

2. DO NOT USE THIS EQUIPMENT EXCEPT ON

SOLID, LEVEL SURFACE WITH CRANE
MOUNTED ON FACTORY-RECOMMENDED
TRUCK.

3. BEFORE OPERATING THE CRANE, REFER TO

MAXIMUM LOAD (CAPACITY) CHART ON CRANE
FOR OPERATING (LOAD) LIMITATIONS.

4. DO NOT OPERATE, WALK, OR STAND BENEATH

BOOM OR A SUSPENDED LOAD.

5. UNPLUG PENDANT AND SHUT OFF MASTER

DISCONNECT SWITCH WHEN CRANE NOT IN
USE.

6. FOR TRAVEL, BOOM MUST BE IN STOWED

POSITION.

DANGER

!

THIS CRANE IS NOT A PASSENGER LIFT

IT IS NOT DESIGNED OR INTENDED TO BE USED TO LIFT,
SUPPORT OR OTHERWISE TRANSPORT PERSONNEL.

YOU MUST NOT

OPERATE THIS CRANE UNLESS:

1.

YOU HAVE BEEN TRAINED IN THE SAFE
OPERATION OF THIS CRANE; AND

2.

YOU KNOW AND FOLLOW THE SAFETY AND
OPERATING RECOMMENDATIONS CONTAINED IN
THE MANUFACTURER'S MANUALS, YOUR

EMPLOYER'S WORK RULES, AND APPLICABLE
GOVERNMENT REGULATIONS.

AN UNTRAINED OPERATOR SUBJECTS HIMSELF
AND OTHERS TO

DEATH OR SERIOUS INJURY .

15391-D

THIS MACHINE IS NOT INSULATED

ELECTROCUTION HAZARD

MAINTAIN SAFE CLEARANCES FROM ELECTRICAL
LINES AND APPARATUS. YOU MUST ALLOW FOR
BOOM SWAY, ROCK OR SAG, AND ELECTRICAL
LINE AND LOAD LINE SWAYING.

THIS LIFTING DEVICE DOES NOT PROVIDE PRO-
TECTION FROM CONTACT WITH OR PROXIMITY
TO AN ELECTRICALLY CHARGED CONDUCTOR.

YOU MUST MAINTAIN A CLEARANCE OR AT LEAST 10

FEET BETWEEN ANY PART OF THE CRANE, LOAD
LINE OR LOAD, AND ANY ELECTRICAL LINE OR

APPARATUS CARRYING UP TO 50,000 VOLTS. ONE

FOOT ADDITIONAL CLEARANCE IS REQUIRED FOR
EVERY ADDITIONAL 30,000 VOLTS OR LESS.

DEATH OR SERIOUS INJURY

WILL RESULT FROM

CONTACT OR INADEQUATE CLEARANCE.

15392-E

DANGER

!

Summary of Contents for HT45KX-20































































Reviews: