background image

11

VUT .. PE EC

CONNECTION TO POWER MAINS

The unit is rated for connection to single-phase ac 230 V/ 50-60 Hz power mains. For electric installations use insulated durable heat-

resistant conductors (cables, wires) with the minimum wire cross section 2.5 mm

2

.The above conductor cross section value is tentative 

and in practice must be based on the wire type, maximum permissible heating temperature, insulation, length and installation method.

Connect the unit to power mains through the external automatic circuit breaker with magnetic trip integrated into the fixed wiring 

system with the rated current not below  the rated current consumption (refer to page 6). 

The terminal block with the prewired control unit is located inside the control unit compartment. To connect the power and the 

ground cable route the cables through the airtight electric lead-in in the unit casing and connect these to the terminal block. The wiring 

diagram for connection of the air handling unit to power supply is on back side of the lid. 

Power

supply 

Digital input (DI)
Digital output (DO)
Analogue input (AI)
Analogue output (AI)

Inside

Outside

Р1

М1

М2

ТE5

ТE1

SM3

230V AC

24V AC

SM2

ТE2

D1

D2

F1

F2

RK1

SM1

Q1

TS1
TS2

HV1

12V AC

ТE6 HV2

RS485

PD1

+

-

PD2

-

FUNCTIONAL DIAGRAM

Designation

Name 

Designation 

Name

  D1*

Supply air  damper 

RK1

Plate heat exchanger 

  D2*

Extract air damper 

  SM1*

Supply damper actuator

F1

Supply filter 

  SM2*

Extract damper actuator

F2

Extract filter 

SM3

Bypass damper electric actuator

M1

Supply fan 

TE1

Outer air temperature sensor

M2

Exhaust fan 

TE2

Temperature sensor at heat exchanger outlet 

P1

Control panel

TE5

Duct temperature sensor

Q1

Electric air heater 

TE6

Room air temperature sensor

  HV1*

Duct humidity sensor 

TS1

Overheat protection thermostat actuated at +50 °С with automatic reset

HV2 

Indoor humidity sensor 

TS2

Overheat protection thermostat actuated at +90 °С with manual reset 

PD1

Differential pressure switch supply filter clogging control

PD2

Differential pressure switch extract filter clogging control

* Not included into the delivery set, available on separate order.

DISCONNECT THE POWER SUPPLY PRIOR TO ANY OPERATIONS WITH THE UNIT.

CONNECTION OF THE UNIT TO POWER MAINS IS ALLOWED BY A QUALIFIED 

ELECTRICIAN WITH A WORK PERMIT FOR THE ELECTRIC UNITS UP TO 1000 V AFTER 

CAREFUL READING OF THE PRESENT USER’S MANUAL. THE RATED ELECTRICAL 

PARAMETERS OF THE UNIT ARE GIVEN ON THE MANUFACTURER’S LABEL. 

ANY TAMPERING WITH THE INTERNAL CONNECTIONS IS PROHIBITED AND WILL VOID 

THE WARRANTY.

Summary of Contents for VUT 1000 PE EC





















Reviews: