background image

12

EN

The product is in compliance with EU norms and standards on low voltage guidelines and electromagnetic compatibility. 
We hereby declare that the product complies with the provisions of Electromagnetic Council Directive 2014/30/EU, Low 
Voltage Directive 2014/35/EU and CE-marking Directive 93/68/EEC. This certificate is issued following test carried out on 
samples of the product referred to above.
The manufacturer hereby warrants normal operation of the unit for 60 months after the retail sale date provided the user's 
observance of the transportation, storage, installation, and operation regulations. Should any malfunctions occur in the 
course of the unit operation through the Manufacturer's fault during the guaranteed period of operation, the user is entitled 
to get all the faults eliminated by the manufacturer by means of warranty repair at the factory free of charge. The warranty 
repair includes work specific to elimination of faults in the unit operation to ensure its intended use by the user within the 
guaranteed period of operation.  The faults are eliminated by means of replacement or repair of the unit components or a 

specific part of such unit component.

The warranty repair does not include: 

•  routine technical maintenance
•  unit installation/dismantling 
•  unit setup
To benefit from warranty repair, the user must provide the unit, the user's manual with the purchase date stamp, and the 
payment paperwork certifying the purchase. The unit model must comply with the one stated in the user’s manual. Contact 

the Seller for warranty service. 

The manufacturer’s warranty does not apply to the following cases:

•  User’s failure to submit the unit with the entire delivery package as stated in the user’s manual including submission with 

missing component parts previously dismounted by the user.

•  Mismatch of the unit model and the brand name with the information stated on the unit packaging and in the user's 

manual.

•  User’s failure to ensure timely technical maintenance of the unit.
•  External damage to the unit casing (excluding external modifications as required for installation) and internal components 

caused by the user.

MANUFACTURER’S WARRANTY

Summary of Contents for Simple 100





















Reviews: