background image

12

Brig HRV 200 (300)

SERVICING AND MAINTENANCE 

 

Servicing of the unit  is required 3-4 times per year. Besides general cleaning, the following 

operations are required: 

1. 

Filter maintenance (3-4 times per year)

 

Dirty filters increase air resistance in the system and reduce supply air flow to the premises.  

 

 

Clean or replace the filters as often as required, but at least 3-4 times per year. 

Clean the filter with running  water or a vacuum cleaner.

 

 

 After two cleaning replace the filter. Contact your local supplier for new filters. 

2.  

Heat recovery core  maintenance (once per year). 

 

Some dust can get accumulated on the heat recovery core block even if you clean or replace 

the filters regularly in compliance with above procedure. To maintain the high heat exchange efficiency, 

pull out and clean the heat recovery core  with warm detergent solution. Re-install the dry heat recovery  

to the unit. 

     3.  

Fan maintenance (once per year). 

 

Even if you perform regular maintenance of the filters and the heat recovery core, some dust 

and grease can get accumulated inside the fans and reduce the fan performance and supply air flow. 

 

Clean the fans with a soft brush or dry cloth. No water and abrasive detergent, sharp objects 

or solvents are allowed for cleaning to prevent the impeller damage. 

4. 

Condensate drainage system maintenance (once per year).

 

The drain hose can get clogged with the extracted particles. Clean the drain hose is required. 

Check proper functioning of the drain system by pouring some water into the drain pan at the unit 

bottom. Clean the U-trap and the drain tubes if required. 

5. 

Supply air flow inspection (twice per year).

 

Leaves and other objects can clog the intake grille and decrease  the unit performance and 

supply air flow. Check the intake grille twice per year and clean it if required. 

6. 

Air ductwork maintenance (once in 5 years).

 

Even if you fulfill all the above maintenance guidelines regularly, a certain amount of dust is 

accumulated inside air ducts. That reduces the ventilation system performance. Clean or replace the air 

ducts periodically. 

Summary of Contents for brig HRV 200

















Reviews: