Ventair SUNB2000BL Instruction Manual Download Page 4

18.  This appliance is not intended for use by persons (including 

children) with reduced physical, sensory or mental capabilities 

or lack of experience and knowledge unless they have been 

given supervision or instruction concerning the use of the 

appliance by a person responsible for their safety. Children 

and vulnerable people should be supervised to ensure they do 

not play with the appliance. 

19.  Use this heater only as described in this manual. Any other 

use not recommended by the manufacturer may cause fire, 

electric shock, or injury to persons. 

20.  Do not operate any heater with a damaged cord or plug or 

after the heater malfunctions, has been dropped or damaged 

in any manner. Disconnect power at service panel and have 

heater inspected by a reputable electrician before reusing. If 

the supply cord is damaged in any way, it must be replaced by 

the manufacturer or its service agent or a similarly qualified 

person in order to avoid a hazard. 

21.  Do not run cord under carpet. Do not cover cord with throw 

rugs, runners, or similar coverings. Do not route cord under 

furniture or appliances. Arrange cord away from traffic area 

and where it will not be tripped over. 

22.  To disconnect heater, turn controls to off, then remove plug 

from outlet. 

23.  To prevent overheating of this appliance, keep the air inlets 

and outlets clean and free of anything that may cause 

blockage. Check all inlets and outlets from time to time to 

ensure it is clear of any dirt or dust accumulation. DO NOT 

COVER. 

24.  Do not use it in areas where gasoline, paint, or flammable 

liquids are used or stored. 

25.  Parts of the heater may exceed 200

, contact with the heating 

tube, reflector, or mental parts near the heating tube, may 

cause severe burns. To avoid burns, do not let bare skin touch 

hot surfaces. 

26.  NEVER place hands under the heating elements. ALWAYS 

allow heating element to cool at least 10 minutes before 

Summary of Contents for SUNB2000BL









Reviews: