Vendor EF27B Owner'S Manual Download Page 9

 

9

 

 

 

STEP 8.

  Thread the two M5x40 wood screws (3) through the center post holes, into the pilot holes, 

and 

into the wall stud

. Partially tighten. Make sure the bracket is level. Thread the four M4x30 

drywall anchor screws (4) through the wall mount bracket and into drywall anchors.   

DO NOT OVER- TIGHTEN

 as this may loosen the anchors or damage the drywall.  Check the 

alignment and tighten each screw securely with the Phillips screwdriver. Check that the bracket is 
secure. 

 

 

ALWAYS unplug 

this fireplace heater

 before assembly 

or

 cleaning, or before 

relocating.  

Failure to do so could result in 

electric shock

fire

, or 

personal injury

 

 

 

 

 

 

STEP 9.

  With the firebox (A) at an angle, fit the slots in the back of firebox (A) over the hooks on 

the wall mount bracket, and carefully press the top of the firebox against the wall mount bracket. 
The slots at the top edge of the firebox should slide over the wall mount bracket tabs.  Hold the 
firebox in place and thread the machine screws (6) through the holes in the firebox and into the wall 
mount bracket tabs. Tighten both machine screws and make sure the firebox is secure to the wall.  

 

4

3

3

4

6

Meijer.com

Summary of Contents for EF27B

















Reviews: