background image

 

2016.09 

 

  3 / 28

 

1.  INTRODUCTION 

Installation,  Operation  and  Maintenance  Instruction  concerns  VHR  DX  heat  pump  heat  recovery  units 
manufactured  by  VENCO.  It  consists  of  basic  information  and  recommendation  concerning  the  design, 
technical specifications, installation, operation and maintenance of the heat pump heat recovery unit which 
shall be obeyed to ensure proper operation of the unit. The key to proper and safe operating of the unit, read 
thoroughly this instruction, use the unit according to guidelines given in it and follow all safety requirements. 
The instruction should always be in proximity of the unit and within easy reach of the service technician.  

 

 

 

 

 

 

2.  HEAT RECOVERY UNITS and VHR MODELS  

VENCO Heat Recovery Units are classified 8 different models; VHR 05 DX 

– 07 DX – 10 DX – 15 DX -     20 

DX 

– 21 DX – 30 DX – 40 DX (Figure 2.1.). In all models, the housing is made from epoxy coated galvanized 

sheet metal and the cabinet is fully insulated for sound and heat isolation.  

 

 

Figure 2.1.1 VENCO VHR DX HEAT PUMP HEAT RECOVERY UNIT 

 

READ THE INSTRUCTION BEFORE START-UP THE UNIT and KEEP THE MANUAL 
CLOSE TO THE UNIT FOR EASY REACH OF SERVICE TECHNICIAN. 

 

THE UNIT MUST BE OPERATED  APPROPRIATE  APPLICATIONS FOR PURPOSES  
DESIGN AND TECHINICAL SPECIFICATIONS OTHERWISE THE REPONSIBILITY OF 
ANY PROBLEM WILL NOT BE  IN WARRANTY TERMS 

 

THE  UNIT  MUST  NOT  USED  IN  THE  ENVIROMENTS  WHERE  CORROSION  and 
EXPLOSIVE GAS EXIST 

 

 

THE  APPLIER  WILL  BE  RESPONSIBLE  FOR  DEFECTS  OCCURED  DUE  TO 
OPERATING  THE  UNIT  BY  NOT  AUTHORIZED  PERSON  or  USING  THE  SPARE 
PARTS WHICH ARE NOT ORIGINAL. 

Summary of Contents for VHR 05 DX






























Reviews: