background image

- 30 -

User Manual 

Athena

English

•   To change parameter status, press 

[OK]

, make your selection using keys   and   

and confirm by the 

[OK]

 key.

•   The time changing date and hour cannot be altered:

 

°

  winter     summer change:  last Sunday in March, at 02:00

 

°

  summer    winter change 

last Sunday in October, at 03:00 

DAILY PROGRAMMING 

•   ABy the daily programming menu it is possible to assign a temperature profile to every 

day of the week, i.e. a   daily program (per control zone). This menu is marked by 

symbol 

.

•   Daily programs are organised by half-hour steps and 

are only enabled during automatic operation. 

•   The user can configure 14 daily programs, which will be 

identified as P00…P13: winter programs from P00 to 

P06, summer programs from P07 to P13.

•   The temperature zone that the programming will affect 

is the one appearing before entering the menu. The 

readings   /   stand for winter and summer programming respectively.

•   The reading of daily programming starts from the current day. Use arrow keys   and 

 to scroll the days of the week and view the daily programs as configured.

•   To change the current program press 

[OK]

. The number identifying program number 

(i.e. P00) will start to flash.

•   Change the current program selection using the arrow keys   and   and choosing 

among the pre-set programs. To change the current program instead, press the  

[OK]

 key.

1

2

3

4

5

6

7

8

9

13 14 15 16 17 18 19 20 21 22 23

11 12

10

1

2

3

4

5

6

7

8

9

13 14 15 16 17 18 19 20 21 22 23

11 12

10

ESC

1

2

3

4

5

6

7

8

9

13 14 15 16 17 18 19 20 21 22 23

11 12

10

ESC

ESC

1

2

3

4

5

6

7

8

9

13 14 15 16 17 18 19 20 21 22 23

11 12

10

Summary of Contents for Athena

























Reviews: