background image

www.velodyne.com

2 - SPL-800i User’s Manual 

PREPARE FOR INSTALLATION

your new Velodyne subwoofer provides for a number of installation options. Read all the installation information 

below in order to determine which installation option is best suited for your system. Remember to perform all 

installation procedures with system power turned off to prevent possible damage.

PLACEMENT

True  subwoofers  operate  at  extremely  low  frequencies  which  are  primarily  omni-directional.  While  it  is 

recommended that the subwoofer be placed on the same plane as the satellite speakers, room and system 

conditions often dictate otherwise. Keep in mind that frequency response and output level can be drastically 

influenced by placement, depending on the acoustic properties of the listening room. Typically, the optimum 

location for a subwoofer is tucked away in a corner of your listening room. This location will usually offer the 

greatest output levels and optimum low frequency extension. The worst location for a subwoofer is typically far 

away from any walls and close to the center of your room. Avoid these locations when possible. when using 

a pair of Velodyne subwoofers in stereo, it is preferable to place each subwoofer by the satellite of the same 

channel.

Caution! This subwoofer has electronics built into the cabinet. Do not place the cabinet next to sources of 

heat such as furnace registers, radiators, etc. Do not place the unit near sources of excessive moisture, such as 

evaporative coolers, humidifiers, etc. The power cord should be routed in such a way that it will not be walked 

on, pinched or compressed in any way that could result in damaging the insulation or wire.

Regardless of where you install your Velodyne subwoofer, it must remain in an upright position (woofer facing 

forward). Using, shipping or storing the subwoofer in any other position for an extended period of time may 

result in damage to the unit not covered by warranty.

your new Velodyne subwoofer, like any good speaker system, requires proper positioning within the listening 

space  to  provide  maximum  performance.  Improperly  placed  speakers  may  degrade  the  sound  quality  and 

reduce your listening pleasure. Depending on the size and type of furnishings in the room, perfect placement 

may not be possible. Finding the best location within your environment will likely require some experimentation. 

We suggest you experiment with the location during setup to find what sounds best to you when seated in your 

typical listening position.

Summary of Contents for SPL-800i





















Reviews: