background image

 

Features : 

 

R

6 x 36mm high digits.  

R

Time, date & temperature indication, selectable with toggle option. 

R

1 sec. resolution chronometer with lap function. 

R

Count down function to a specific date. 

R

Scoreboard function (two players or teams, count up to 199). 

R

Random generator from 00 to 99. 

R

2 digit dice. 

R

Hour chime option. 

R

Counter display. 

R

Relay output for temperature control or time alarm. 

R

US or Europe display option: time, date, degrees Celsius or Fahrenheit. 

R

Wireless remote control for all functions (wired remote possible). 

R

Optional enclosure type B8009. 

R

Optional extra 

remote type K6706A, K6706B or K6706G.

 

Total solder points: 775 
Difficulty level:  

 beginner

 1

o

  2

o

  3

o

  4

o

  5

þ

 

advanced

 

Multifunctional clock display

 

ILLUSTRATED ASSEMBLY MANUAL                                                                    H8009IP-3 

Specifications : 

 

Fixed 433.92 MHz transmitter frequency, as required by law. 

Key chain remote control included. 

Temperature indication from -20 to +70 ºC (resolution 1º). 

Temperature indication from 0 to +150 ºF (resolution 2º). 

Memory backup option: 9V battery or rechargeable battery T331 

Relay output: 1A / 24V max. 

Supply: 12VDC/300mA power supply (adapter type PS1203). 

Dimensions : 252 x 80mm (without enclosure). 

K8009

 

Modifications reserved 

Summary of Contents for H8009

























Reviews: