Veit SF26 Operating Instructions Manual Download

Page: 45 / 149

7.2.4 Manual mode

Manual mode is only active when the "MANUAL" screen

Chapter 7.3.1.6.8 „Manual mode“ on page 62

is displayed on the

control panel.
All the functions can be moved and controlled individually.

CAUTION!
Risk of injuries.

In manual mode, the safety functions are only acti-

vated to a limited extent. There is a
– Risk of crushing

– Risk of burns

7.2.5 Automatic mode

Automatic mode can only be performed when the "operating mode"

screen is displayed on the touch screen.
Pressing the right pedal when the machine is in idle state starts

automatic mode.
Automatic mode includes the following functions:

Manually placing the garment when the tensioning elements

are closing

Automatic finishing cycle (steaming, drying)

Manually removing the garment after opening the tensioning

elements

After garment removal, the machine is in idle state again.

Operation

Operating state of the machine > Automatic mode

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands