Veit SF26 Operating Instructions Manual Download

Page: 62 / 149

Time wait till save energy
(only with save energy option)

Sets the out-of-operation period after which the shirt finisher switches

to energy-saving mode.

Runtime fan heating up
(only with save energy option)

Sets the time the fan runs in order to heat up the bust after energy-

saving mode has been stopped.

7.3.1.6.6 Alarm

Alarm

Displays alarm and warning notes as a history.

7.3.1.6.7 Language

Pressing the flag button selects the according language.

Language selection is accepted.
Screen switches to operating mode.

7.3.1.6.8 Manual mode

CAUTION!

When pressing the button, the following warning

note appears:

"Do you want to activate manual

operation? Attention!!! Security functions are

limited".

Accept safety note
Cancel procedure

Fig. 18: Alarm (EN)

Fig. 19: Language touch screen (EN)

Fig. 20: Manual mode touch screen

(EN)

Operation

Controls and indicators > Control panel

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands