Version 0.3
3 November 2004
For use with Vega 25 version 2.0.10 or greater.
© 2004 VegaStream Ltd.
Configuration information is for example only – test well before deploying.
1. Connect your Vega to LAN, Telephone and Power
LAN:
Using the supplied LAN cable connect the LAN port on the Vega 25 to a standard or fast Ethernet
hub or switch (10 baseT or 100 baseTx).
Telephony:
Plug a phone into the Phone socket and the PSTN line into the Line socket.
Power:
Insert the power cable into the power inlet on the Vega 25 marked “DC 5V”. Plug the other end
into the mains supply. The “ACT” power LED by the “DC 5V” connector will illuminate (and flash).
2. Configure the basic LAN parameters
If a DHCP server is available, the Vega will automatically pick up an IP address.
To find the IP address of the Vega 25, pick up the phone handset attached to the Vega:
Press * * * *
Press 110#
The IP address will be read back.
If this is wrong, or other IP configuration needs to be carried out, see the Installation and Initial
Configuration guide, or the instructions in Appendix 2 and Appendix 3 of this document.
3. Configure Vega 25 to Vega 25 operation
Configuration is carried out using a web browser.
Enter the IP address of the Vega into the “Address” field of your web browser, preceded
by http:// and followed by admin/advanced
e.g.
http://192.168.1.10/admin/advanced
Select the
Line 1
tab:
In the
SIP Settings
section:
SIP Port
5060
In the
Proxy and Registration
section:
Proxy
IP address of the destination Vega gateway
Register
no
Use OB proxy in Dialog
no
Make call without reg
yes
Ans call without reg
yes
In the
Subscriber Information
section:
This subscriber information is not actually used to route calls, so can be any values that do not clash with other devices
Display name
dummy display name, e.g. London PBX
User ID
set to the telephone number to be used for this line, e.g. 5501
In the
Dial Plan
section:
Dial Plan
( S0 <:6602>)
where 6602 is the phone number of the PSTN port on the destination Vega
Press
Submit all changes
Version 0.3
3 November 2004
For use with Vega 25 version 2.0.10 or greater.
© 2004 VegaStream Ltd.
Configuration information is for example only – test well before deploying.
Select the
PSTN Line
tab:
In the
NAT Settings
section:
NAT Keep Alive Enable
no
In the
SIP Settings
section:
SIP Port
5060
In the
Proxy and Registration
section:
Proxy
set this to the IP address of remote gateway
Register
no
Use OB proxy in Dialog
no
Make call without reg
yes
Ans call without reg
yes
In the
Subscriber Information
section:
Display name
dummy display name, e.g. Washington PBX
User ID
set to the telephone number of this line, e.g. 5502
In the
Dial Plans
section:
Option 1: ---------
Dial Plan 2
(S0<:6602>)
Dial Plan 3
(xx.<:@gw0>)
In the
VoIP to PSTN Gateway Setup
section:
VoIP-To-PSTN Gateway Enable
yes
VoIP Caller Auth Method
None
Default VoIP caller DP
3
In the
PSTN-To-VoIP Gateway Setup
section:
PSTN-To-VoIP Gateway Enable
no
Option 1: ---------
yes
PSTN Ring Thru Line 1
no
Option 1: ---------
PSTN Caller Default DP = 2
In the
FXO Timer Values (sec)
section:
PSTN Answer Delay
0
Press
Submit all changes
Select the
Regional
tab
In the
Control Timer values (sec)
section:
Interdigit Long Timer
5
In the
Miscellaneous
section:
Caller ID Method
ETSI FSK With PR(UK)
Press
Submit all changes
