manualshive.com logo in svg

VeEX VePAL TX300M, User Manual


Share
Download
background image

Pattern

Tapping the Tx Pattern box opens the Tx Pattern Setup screen.

Tx Pattern Setup

PRBS Pattern: 

Use the pattern drop-down box to select the test pattern which will be inserted into the transmitted signal.

Pseudo Random Bit Sequences (PRBS) defined by ITU-T 0.150 and 0.151 standards, fixed words and 24-bit or 32 bit user

defined patterns are available. Note, if the 32 bit user pattern entered is incorrect, the default pattern will be 0xFFFFFFFF.

Invert:

 Inversion of polarity is also available.

Go back to top

 

Go back to TOC

6.3.2 Receiver Setup

Hierarchy

Tapping the Hierarchy setup box opens the Rx Hierarchy screen. The Hierarchy setup options for the Rx are the same as for the

Tx described previously.

Rx Hierarchy Setup

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Reviews:

No comments

Related manuals for VePAL TX300M

Yamaha A3000 Upgrade Manual preview
A3000
Brand: Yamaha Pages: 50
A&D PT Series Instruction Manual preview
PT Series
Brand: A&D Pages: 30
dbx 911 Instruction Manual preview
911
Brand: dbx Pages: 12
dbx QUANTUM Application Manual preview
QUANTUM
Brand: dbx Pages: 13
dbx 1066 Operation Manual preview
1066
Brand: dbx Pages: 72
dbx AFS224 Quick Start Manual preview
AFS224
Brand: dbx Pages: 11
dbx 566 Owner'S Manual preview
566
Brand: dbx Pages: 16
Garelick 40016 Quick Start Manual preview
40016
Brand: Garelick Pages: 2
Gardico 60087 Manual preview
60087
Brand: Gardico Pages: 2
OceanSat AIS Manual preview
AIS
Brand: OceanSat Pages: 85
iFIT TT200 Patient User Manual preview
TT200
Brand: iFIT Pages: 11
jablotron JA-65ST Quick Start Manual preview
JA-65ST
Brand: jablotron Pages: 2
PacBio Sequel Safety Manual preview
Sequel
Brand: PacBio Pages: 13
Pablo BELMONT Assembly/Installation Instructions preview
BELMONT
Brand: Pablo Pages: 4
PA A42R-316 Manual preview
A42R-316
Brand: PA Pages: 28
Waters 2707 Quick Install Manual preview
2707
Brand: Waters Pages: 4
Waterpik ClearView Instructions For Use preview
ClearView
Brand: Waterpik Pages: 2
B.E.G. LUXOMAT net PBM-KNX-DX-4W Manual preview
LUXOMAT net PBM-KNX-DX-4W
Brand: B.E.G. Pages: 16

Brands by name

Popular brands

Load more brands