VeEX UX400 User Manual Download Page 201

Page: 201 / 209

7.7.2 E1 Frame Words

This function requires the E1 signal to be framed. The NFAS word is used to carry information about the status of the link and to

provide control signals for primary rate multiplexers.

Bit 1: Reserved for International use (M is used to transmit the CRC multiframe signal in PCM30C and PCM31C)

Bit 2: Set to “1” to prevent simulation of FAS

Bit 3: "A" shows the remote alarm indication

Bits 4 to 8: Sa4 to Sa8 are spare bits

TX:

Bits Sa4 to Sa8 are used to send optional network messages. The Sa bits should be set to “1” when they are not used or

when links cross International borders.

RX:

Bit Sa4 can be used as a message based data link for operations, maintenance and performance monitoring.

E1 Framed RX

UX400 10G e-Manual D07-00-058P RevA00

Page 201 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands