EMR
3
Setup and Operation Manual
C&C Mode Setup Categories
45
Figure 49. Delivery and Shift Report Formatting Examples
RESTART
Figure 50 illustrates the Restart procedure in C&C Mode.
CAUTION: DO NOT USE UNDER NORMAL
CONDITIONS!
Do not press NEXT at the restart message unless you want to reboot the Display Head.
Figure 50. Restart Options
You want to modify the example Delivery
Ticket format as follows:
• Move TICKET NUMBER from line 10 to 15
• Replace the original TICKET NUMBER
label on line 10 with a blank line
• Delete the TOTALIZER START label
Procedure
1. Copy TICKET NUMBER to the
TOTALIZER START line.
2. Copy any blank line (e.g., line 11) to the
original TICKET NUMBER line (10).
The change appears as shown below:
You want to modify the example Delivery
Ticket format as follows:
• Switch TANK ID and METER ID labels
Procedure
Since moving is copying, you have
to save one of the two lines first.
Think of the lines following the first END
OF REPORT line (line 38 in the default example)
to line 75 (last possible line) as a scratch pad
You do not have to go back and write
over line 38 since all lines after the first
END OF REPORT line (in the example, line 37)
are ignored.
IMPORTANT! If you want to insert a line you
will have to copy each line below the insert
point to the scratch pad (lines after the first
END OF REPORT line - lines 38 through 75 in the
default format), then copy them back into the
format below the inserted line, one by one.
Before beginning an insert, on a clean sheet
of paper, list each line number and label you
want in the finished report. After you copy
all of the necessary lines from the default
report into the scratch pad, you can easily use
your handwritten report as a guide when copying
each line back into the final report.
Line 1
Line 2
Line 3
Line 4
Line 5
Line 6
Line 7
Line 8
Line 9
Line 10
Line 11
Line 12
Line 13
Line 14
Line 15
Line 16
Line 17
Line 18
Line 19
Line 20
Line 21
Line 22
Line 23
Line 24
Line 25
Line 26
Line 27
Line 28
Line 29
Line 30
Line 31
Line 32
Line 33
Line 34
Line 35
Line 36
Line 37
END OF REPORT
Veeder-Root Co.
EMR-3
(blank)
(blank)
(blank)
START
FINISH
(blank)
TICKET NUMBER
(blank)
PROD DSCRPT 1
METER ID
TANK ID
TOTALIZER START
TOTALIZER END
VOLUME GAL START
GROSS VOLUME FINISH
NET VOLUME FINISH
AVG FLOW RATE (GPM)
TEMP THIS DELIVERY
VOLUME CORRECTED TO
COEFFICIENT OF EXPANSION
PRICE/GALLON
SUBTOTAL
% TAX T/D 1
FINAL PRICE/GALLON
TOTAL NON-TAX LINES
TAX THIS DELIVERY
GRAND TOTAL
CS TEST FAILURE
(blank)
You can count on us!
(blank)
(blank)
(blank)
END OF REPORT
Delivery Ticket (Example)
Example 1 - Moving a line
Example 2 - Switching 2 lines
Inserting a line
(blank)
(blank)
PROD DSCRPT 1
METER ID
TANK ID
TICKET NUMBER
Line 10
Line 11
Line 12
Line 13
Line 14
Line 15
PROD DSCRPT 1
TANK ID
METER ID
TICKET NUMBER
Line 12
Line 13
Line 14
Line 15
in which you can 'save' labels while you move
them around.
1. Copy METER ID line 13 to line 38.
2. Copy TANK ID line 14 to line 13.
3. Copy METER ID line 38 to line 14.
The change appears as shown below:
Prints only if TC enabled
Prints only if TC not enabled
SECURITY CODE
LANGUAGE
DISPLAY SYNTAX
TEMPERATURE
FUEL SOURCE
METER CALIBRTN
CONFIGURE I/O
OEM MESSAGE
DELIVERY OPTIONS
REPORT FORMATS
PRESERVE NVRAM
INIT NVRAM
+
-
+
-
+
Press the up/down
buttons to cycle
through remaining
C/C Mode categories
NEXT
RESTART
Press ENTER
to reboot and perform a self-
test of the Display Head, without
changing any setup parameters
or resetting the Grand Totalizer to 0.
CAUTION!
Pressing ENTER you:
• Reboot and perform a self-test of the Display Head
• Restore all setup parameters to the factory default settings
• Reset the Grand Totalizer count to 0
• Clears all stored transaction records
ENTER
ENTER
CAUTION! DO NOT USE UNDER NORMAL CONDITIONS!
Do not press NEXT at the Restart message
unless you want to reboot the Display Head.
If you have pressed NEXT and are viewing the
message below, but don't want to reboot, you
can exit C&C Mode by pressing the MODE
button to avoid rebooting.
IMPORTANT! Prior to initializing NVRAM:
• Print a ticket,
• Record the totalizer value, and
• Record the calibration values.
