Veeco 004-210-000 Instruction Manual Download Page 203

Page: 203 / 358

Force Imaging

Force Calibration Control Panels and Menus

Rev. B

MultiMode SPM Instruction Manual

183

11.3 Force Calibration Control Panels and Menus

The

Force

Calibration

Control

window (see

Figure 11.3a

) manipulates the microscope in

Force

Calibration

mode. The parameters control the rate, start position and amplitude of the triangle

wave applied to the Z piezo. You can also adjust the

Setpoint

value of the cantilever de

ection

voltage used in the feedback loop during imaging. The

Capture

button stores the force curve for

ine

viewing. Some parameters in

uence the operation of the microscope during imaging; most

of the menu parameters affect only

Force Calibration

mode.

Figure 11.3a

Advanced Force Calibration Control Window (Contact Mode AFM)

There are 2 methods to enter Force Calibration Mode:

•

View

Force Mode

Calibrate

will open a simpli

ed subset of the parameters and

commands available.

•

View

Force Mode

Advanced

includes the full set of available parameters and

commands.

Additionally:

•

View

Force Mode

Step

enters force mode with the parameter

start mode

step

and the piezo fully retracted.

•

View

Force Mode

Volume

enters Force Volume Mode.

Items in the

Force Calibration

Control

Window are discussed individually below.

038

Summary of Contents for 004-210-000







































































































































































































































































































































































Search results

Summary of Contents for 004-210-000

Reviews:

Veeco 004-210-000, Instruction Manual, Page: 203 / 358

Search results

Summary of Contents for 004-210-000

Reviews: