background image

HFT-1500 Digital Antenna Tuner with Roller Inductor 

Owner's Manual

 

 

INSTALLATION 

 
Carefully unpack your HFT-1500 from the packing carton and inspect it for signs of 
damage.  If any damage is apparent, notify the transportation carrier or dealer 
immediately.  We recommend keeping the packing carton for moving, storage, or 
reshipping the tuner. 
 
Select a location for the HFT-1500 that allows the connectors to be free of any possible 
contact during operation. 
 

WARNING:  SOME BALANCED OR END-FED ANTENNAS WILL PRODUCE 

HIGH RF VOLTAGES AT THE BANANA CONNECTORS.  RF 
BURNS MAY RESULT IF TOUCHED DURING TRANSMISSION.

 

 

INSTALLATION PROCEDURES 

1.  Connect a coax cable from your transmitter or receiver to the RF INPUT connector on 

the rear panel.  Keep the cable as short as possible.  If you use a linear amplifier, 
connect your transmitter to the linear amplifier output to the HFT-1500.  

Do not use 

more than 1000 watts average (single tone) through the tuner.

 

2.  Connect coax cable(s) from your antenna to COAX 1 or COAX 2 connectors on the 

rear panel.  These connectors are either direct from the transmitter or through the 
tuned circuit depending on the setting of the OUTPUT SELECTOR switch on the 
front panel. 

3.  If you are using a balanced feed antenna, connect a balanced line to the BALANCED 

OUTPUT connectors and jumper banana jack (8) with lower jack (7) as shown by 
dotted line. 

4.  If using a single wire antenna, connect it to post (7) without installing jumper. 

5.  Connect a dummy load to the BYPASS (4) connector using a coax cable.  This lets 

you select the dummy load from the OUTPUT SELECTOR switch.  Any antenna that 
does not require the use of an antenna tuner may be connected to the BYPASS 
connector, if desired. 

 

BEFORE OPERATION 

1.  To avoid possible damage to the HFT-1500, set TRANSMITTER, ANTENNA, 

INDUCTOR, and POWER RANGE switches as outlined in the next section before 
applying transmitter power. (Tuning Section) 

2.  Begin tuning with your transmitter set at a low power setting 

(50 to 100 W) 

 

WARNING:  DO NOT OPERATE THE HFT-1500 WITH THE COVER OFF!   

 

Summary of Contents for HFT-1500














Reviews: