background image

11

6.

AIR COMPRESSOR/TIRE INFLATOR

IMPORTANT:

Read Instructions Carefully To Avoid Possible Injury Or Property Damage.

The built-in 12 Volt DC air compressor is the ultimate compressor for all vehicles,

trailer tires and recreational inflatables. Three different sized nozzles are supplied.

Each nozzle will clip on the end of the standard tire valve connector located at the free

end of the compressor hose. The compressor nozzles are stored inside the hose hatch.

The compressor hose with tire fitting is stored in a retaining channel between the

jumper cable channels on the rear of the unit.  The ON/OFF Switch is located on the

side of the Main Unit near the AC Recharge Port. The compressor can operate long

enough to fill up to 3 average sized tires before the battery must be recharged.

The compressor may be used by removing the air hose from the storage hatch and if

required, fitting an appropriate nozzle to the air hose.  An On/Off switch located on

the side of the unit controls the power to the compressor and the gauge light. Refer to

Figures 3 for locations of compressor hose, nozzle storage hatch and hose. Return

hose to the storage compartment after use.

6.1

WARNINGS FOR COMPRESSOR USE

The compressor is capable of inflating up to 260 pounds per square inch (PSI)

pressure. To avoid over-inflation, carefully follow instructions on articles to be

inflated. Never exceed recommended pressures. Bursting articles can cause

serious injury. Always check pressure with the pressure gauge. Never leave

compressor unattended while in use. Allow unit to cool after 10 minutes of

continuous operation.

6.2

TIRE INFLATION OR PRODUCTS WITH A VALVE STEM

1. Place connector (chuck) on valve stem.

2. Push connector toward valve stem and close thumb latch.

3. Make sure connector is pushed on to valve stem as far as possible before

closing thumb latch.

4. Check pressure with the pressure gauge.

5. When desired pressure is reached, Turn OFF Compressor Power Switch.

6. Remove Compressor hose and chuck.

7. Store compressor hose and tire fitting in storage compartment.

COMPRESSOR

HOSE, NOZZLE

STORAGE HATCH
AND HOSE

ADAPTERS

Vec021APC manual 10/02

12/3/02, 10:57 AM

11

Summary of Contents for Start-It VEC021APC

















Reviews: