background image

X1DW 

VDO CYCLECOMPUTING

8

GB

SLO

PL

JP

JP

PL

SLO

GB

www.vdocyclecomputing.com  

 X1DW

9

3.2  Cadence option

The cadence menu is only available if

B

  the cadence transmitter is installed,

B

  the transmitter was recognized during pairing.

After pairing the cadence transmitter, the current ca-
dence is shown in section 2 of the display.
In function mode it is possible to select the CADENCE/
MORE menu using the     using the up/down 
buttons.

Confirming with 

M

 opens the menu and gives you 

access to the information.

Using     you come to:

B

  AVG CADENCE

B

  MAX CADENCE

Resetting the trip data also sets the cadence data 
back to zero.

4. Installation

4.1  Fitting the transmitter, magnet and handlebar holder 

>>> P01

Start by fitting the transmitter and magnet.

ATTENTION: The transmitting distance between 
the transmitter and the computer on the handle-
bars should not be more than 60 cm (transmission 
range).

step 1 

Place the rubber pad under the transmitter. 

Fit the transmitter on the same side of the fork 
where you later want to fit the computer to the 
handlebars (right or left) using the cable ties sup-
plied (loose at first, do not pull tight just yet).

ATTENTION: The sensor mark on the transmitter 
must point to the spokes.

Depending on the room available, the transmitter 
can be fitted at the front on the forks, inner side 
of the fork or backside of the forks.  

>>> P04

step 2

 Place spoke magnet around an outer 

spoke. The silver middle of the magnet points 
towards the transmitter. Align the magnet to the 
sensor mark on the transmitter with a gap 
of about 1 – 5 mm.

step 3

 Align transmitter and magnet for good and 

fasten in place: Pull cable ties tight and push 
magnet in firmly.

step 4

 Decide whether fitting to handlebar or 

stem and turn the base of the handlebar holder 
by 90° accordingly. To do so, undo the screws in 
the holder, take out the foot and turn it 90°, insert 
and tighten the screws again.

ATTENTION: Do not over tighten screws.

To wake it up out of despatch mode, press the

   button simultaneously for a few seconds. 

The computer is now ready for use and tells you 
so by showing the language setting. 

See also Chapter 5.1

4.2 Switching on the computer for the first time 

>>> P02, Display see Chapter 5.1

Waking up from despatch mode 

The computer is delivered with a battery installed. 
To reduce the battery consumption, the computer 
is put into despatch mode. The display is empty 
(no display). 

4.3  Installing the battery in the computer 

>>> P05

Your VDO computer is supplied with a 3V battery 
(type 2032).

The battery is already installed when supplied.

To change the battery, proceed as follows:

step 1 

Place the battery in the computer casing 

with the +terminal facing up.

step 2 

Make sure that the battery does not 

get wedged.

step 3 

Take care that the rubber seal lies flat on 

the battery compartment lid.

step 4 

Insert the battery compartment lid into the 

opening and turn it with a coin to the right as far 
as it will go (approx. 1/3 turn).

TIP for changing battery: VDO recommends  
changing the battery once a year. Buy a new  
battery in good time to ensure the wireless  
transmission works perfectly.  
When the battery is changed, all settings and 
the total kilometres cycled are saved.

step 5 

Guide the cable ties through the slot in the 

handlebar holder, place around the handlebars 
or the stem and pull (do not pull tight just yet).

step 6 

If fitting to handlebar: Align computer 

angle to achieve optimum readability. Now pull 
cable ties tight. Snip off protruding ends with 
clippers.

Summary of Contents for X1DW










































Reviews: