background image

18

M1.1 WR

!

OPEN

CLOSE

NEW

OLD

10 SEC.

1

2

3

Low battery indicator

The M1.1 WR has a low battery warning. 
The text 

“Computer low” 

appears on the display.

Press the 

BIKE button

 to acknowledge this low battery 

warning.
You can keep using the cycle computer for approx. a week. 
Replace the battery as soon as possible on seeing the low 
battery warning.

Replacing the battery in the computer

To ensure your cycle computer is fully functional,  
we recommend 

replacing the battery annually

.

ATTENTION:

 your settings, total distance and total ride time 

information remain stored when you replace the battery.  

NO

 data is lost.

You need a 3 V 2032 battery.
We recommend using a branded battery from Sony,  
Panasonic, Varta or Duracell.

The process is as follows:

STEP 1

Use a coin to remove the battery compartment cover.

STEP 2

Remove the dead battery.

ATTENTION:

 Wait 

for

 10 seconds

 before inserting the new 

battery. The electronics need this time to recognise that the 
battery is being changed.

STEP 3

Insert the battery into the computer housing  
with the +pole up.
Ensure that the battery is not tilted.
Ensure that the rubber seal lies smoothly on the lid of the 
battery compartment.

STEP 4

Insert the battery compartment cover into the opening and 
use a coin to turn it to right as far as it will go.

Summary of Contents for m 1.1 wr























Reviews: