VDO CHD 1002 S User Manual Download Page 2

CONTENTS

USER INSTRUCTIONS

English

INTRODUCTION

2

PRECAUTIONS

WARNING: To prevent short-circuiting, disconnect the negative car battery terminal until the
whole system has been mounted and connected (fig. 1). 

See  separate  installation  card.

Voltage and polarity: 12 V, negative earth.

• Do not attempt to repair or service the CD changer yourself. Return the unit, plus magazine

with the transport screws in place, to your dealer or an 

authorised Service Agency

(see

addresses at the end of this booklet).

• Temperatures inside the parked car will fluctuate considerably during summer and winter.

They should not 70°C or –20°C when operating the CD changer.

• To avoid too high temperature, never install the changer on top of the dashboard or on the

rear parcel shelf.
- If the temperature is too high, a built-in protection mechanism prevents the CD changer

from operating until the temperature reaches a safe level. During this time a warning 
message is displayed by the car radio.

This CD changer is designed for use only with car radios which have CD changer controls 

based

on the DIGITAL standard.

Consult your dealer for suitable types of car radio.

The functions of the CD changer are described in the operating instructions for the car radio.

General

Precautions 

........................................................................................................................................................................

2

Installation

Preparation 

.......................................................................................................................................................................

3

Mounting

...........................................................................................................................................................................

5

Operation

...........................................................................................................................................................................

7

Troubleshooting

.............................................................................................................................................................

9

Specifications

...................................................................................................................................................................

10

Laser Product Class 1

..................................................................................................................................................

10

CHD 602S_GB  4/11/01 1:41 PM  Page 2

Summary of Contents for CHD 1002 S












Reviews: