VDH MC 885-SDHL Manual Download Page 4 | Manualshive

Page: 4 / 10

VDH MC 885-SDHL Manual Download Page 4

No.

Description

Range

Per

Unit

Default

51

52
53
54
55

56

0 = None
1 = Room temperature (absolute)
2 = Channel temperature (absolute) (room temperature if P02 = 0)
3 = Lowest sensor temperature
4 = Highest sensor temperature
5 = Average sensor temperature
6 = Control temperature
7 = Control temperature relative to control setpoint

Minimum alarm detection during

0 =  Spraying
1 =  Drying
2 =  Both modes
(always detection for single setpoint)

Minimum alarm temperature
Switch differential for minimum alarm
Time delay for minimum alarm
Action at minimum alarm
(message with code and alarm relay function always appear in display)

0 = None
1 = Disable all burner control

Reset minimum alarm automatically

(0 = no, 1 = yes)

0 2

-350 +350
0.1 15
0 99
0 1

0 1

-

1
0.1
1
-

-

-



C



C

min
-

-

2

-50
0.1
0
0

0

60

61

62
63
64
65

66

Maximum alarm detection on

0 =  None
1 =  Room temperature (absolute)
2 =  Channel temperature (absolute) (room temperature if P02 = 0)
3 =  Lowest sensor temperature
4 =  Highest sensor temperature
5 =  Average sensor temperature
6 =  Control temperature
7 =  Control temperature relative to control setpoint

Maximum alarm detection during

0 =  Spraying
1 =  Drying
2 =  Both modes
(always detection for single setpoint)

Maximum alarm temperature
Switch differential for maximum alarm
Time delay for maximum alarm
Action at minimum alarm
(message with code and alarm relay function always appear in display)

0 =  None
1 =  Inhibit all burner control
2 =  Inhibit burner high
3 =  Inhibit burner high, replace with

>

burner low

=

Reset maximum alarm automatically

(0 = no, 1 = yes)

0 7

0 2

-350 +350
0.1 15
0 99
0 3

0 1

-

-

1
0.1
1
-

-

-

-



C



C

min
-

-

0

2

+300
0.1
0
1

0

70

71

72
73
74
75

Maximum limit on

0 =  None
1 =  Room temperature (absolute)
2 =  Channel temperature (absolute) (room temperature if P02 = 0)
3 =  Lowest sensor temperature
4 =  Highest sensor temperature
5 =  Average sensor temperature
6 =  Control temperature
7 =  Control temperature relative to control setpoint

Maximum limit during

0 =  Spraying
1 =  Drying
2 =  Both modes
(always limit for single setpoint)

Maximum temperature limit
Switch differential for maximum limit
Time delay for maximum limit
Action at maximum limit

0 =  No limit (same as P70 = 0)
1 =  Inhibit all burner control
2 =  Inhibit burner high
3 =  Inhibit burner high, replace with

>

burner low

=

0 7

0 2

-350 +350
0.1 15
0 99
0 3

-

-

1
0.1
1
-

-

-



C



C

min
-

0

2

+300
0.1
0
1

«
...
2
3
4
5
6
...
»

Summary of Contents for MC 885-SDHL











Reviews:

No comments