Vayyar Home Dry Contact Installation Manual Download Page 54

FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the 
separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes 
or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate 
this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference received, including interference 
that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with 
any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. 
Selection of other channels is not possible. FCC Radiation Exposure Statement: This equipment complies with FCC radiation 
exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 
distance 20cm between the radiator & your body

FCC Statement

Vayyar Home 

  

Dry Contact Installation Guide   

Vayyar.com

Copyright © 2021 Vayyar Imaging Ltd. All rights reserved. Vayyar and 

Vayyar Home are trademarks and/or registered trademarks of Vayyar 

Imaging Ltd, 26 Shabazi St, Yehud-Monosson, Israel 5623108.

Summary of Contents for Home Dry Contact
























































Reviews: