background image

 

 

 

 

Page 3 / 4

 

Auto Mode

Off Mode

 Manual

Override

Manual Override Operation Diagram

Turn wall switch OFF-ON 

in 0.5~3 Seconds

Turn wall switch OFF-ON 

in 0.5~3 Seconds

Fig.1

Customization Options

Shut-off Delay

1. The Shut-off delay is the length of time that the light will stay on

    after motion stops.

2. The Shut-off delay can be adjusted by using the "TIME"  knob when

    the slide switch is set in "OFF" or "AUTO" mode. (See Fig.2)

3. The range of shut-off delay is 5 seconds to 3 minutes.

4. Rotate the knob clockwise for increasing the shut-off delay.

5. Rotate the knob counterclockwise for decreasing the shut-off delay.

Sensitivity of Motion Sensor

1. The sensitivity can be adjusted from 5 to 30 feet by using the "SENSITIVITY" knob. (See Fig.2).

2. Turn the knob clockwise for increased sensitivity.

3. Turn the knob counterclockwise for decreased sensitivity.

NOTE:

1. The sensitivity of the motion sensor will increase as the

    environmental temperature gets colder. For best performance, 

    gently clean the lens with a soft cloth every 1 or 2 months to

    ensure maximum sensitivity. 

 

2. When installed at a height of 6.5 feet, at 77 degrees Fahrenheit,

    the light will provide a maximum detection distance of 30 feet

    and detection range of 150 degrees. (See Fig.3, Fig.4)

3. The sensor will be more sensitive to motion across its

     detection path than motion directly towards it. (See Fig.5) 

4. To reduce possible nuisances, do not mount the fixture

    near a heat source like an air conditioner, vent or furnace

    exhaust, or in a direction facing any reflecting object or

    other light source.  

     

Where you install your lantern is important:

Be sure the light is mounted straight on the wall;

otherwise, the detection distance may be limited. 

5`

6`

10`

30`

Fig. 3

Fig. 4

150˚

Least sensitivity

Most sensitivity

Sensor

Fig. 5

Motion

Motion

Fig. 2

 (View from bottom of sensor lens) 

Mode

5S

TEST 3MIN

TIME

OFF AUTO PC SENSITIVITY

TROUBLESHOOTING

Refer to following information to solve your problems.

Set the rotary knob in the test mode for testing.

Night

If the light 

isn’t on

SYMPTOM

DAY/NIGHT

POSSIBLE CAUSE

SOLUTION

Day

Rotary knob is not set in the test 

mode.

Wall switch or circuit breaker is off. Turn on wall switch or circuit breaker.

Test the light bulb on normal working light fixture.

Tighten the light bulb.
Check wire connections.

Relocate fixture away from western facing wall.

Eliminate or turn off other light source, block other

light source from shining onto sensor, or relocate

fixture.

Light bulb may be burned out.

Light bulb is loose.

Incorrect or loose wire connections.
Too much sunlight is shining onto 

sensor in the early evening.
Too much light is shining onto 

sensor due to another light source, 

such as a street lamp or other light 

fixture.

5. Manual Override MODE (nighttime operation only)

    ● 

To shift to the manual override mode, set the switch to "AUTO" or

       "OFF"  mode. Turn the wall switch "OFF" and "ON" within 3 seconds.

       The light will remain on until dawn. To restore to the "AUTO" or "OFF" 

       mode, turn the wall switch "OFF" and "ON" within 3 seconds. 

       (See Fig.1)

     ● 

The light will last for one night only and turn off automatically at dawn.

        

231011

Summary of Contents for T0734













Reviews: