160425
Page 2 / 4
1. Thread two headless screws through the cross bar, and then secure them with four lock nuts (two on each side of
the cross bar). Adjust the length of the headless screws if necessary.
Note: Make sure that the headless screws are lined up horizontally to make the fixture level.
2. Attach cross bar to the outlet box using two mounting screws.
3. Make the bottom of the fixture upward, gently place glass panels into the frame, then press the clips to secure the
glass panels. (See Fig.1)
NOTE: The width of the front glass panel is wider than the width of side glass panel .
4. Secure the curved arm to the fixture with metal pad and the finial, and then attach the curved arm to the back plate,
thread the set screw through the holes of curve arm and the back plate, secure them with a washer and a hex nut.
5. Pull out the source wires from the outlet box. Make wire connections using wire nuts as follows:
---Connect the hot wire (usually black insulation) from the power source to the black wire from the fixture.
---Connect the neutral wire (usually white insulation) from the power source to the white wire from the fixture.
---Attach the fixture grounding wire (usually green insulation or bare wire) to the cross bar with the green grounding
screw, or connect to the source grounding wire if available.
Carefully put the wires back into the outlet box.
6. Attach the back plate to the cross bar by inserting the headless screws, and then secure it with two rubber pads and
two bolt nuts.
NOTE: With silicone caulking compound, caulk completely around where the back plate meets with the wall
surface to prevent water from seeping into the outlet box.
7. Install a bulb (not included). Check relamping label at socket area or packaging for maximum allowed wattage.
Installation Steps
Function and Operation
MODES OF OPERATION
Choose a mode by sliding the switch on the bottom of the back plate of the fixture. (See Fig.4 ).
When power is first applied, the light will turn to high level brightness, wait for 15 seconds to allow the sensor to warm up.
1. TEST MODE (daytime and nighttime operation)
● The light will turn to low-level brightness (0%~50% brightness). The light will turn to high-level brightness (100%
brightness) when motion is detected, and stay on as long as the motion is continuing. The light will revert to
low-level brightness about 5 seconds after motion is no longer detected.
2. 3H MODE (nighttime operation only)
● At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%
~50% brightness) automatically after 3 hours. The light will turn to high-level brightness (100% brightness) when
motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light
will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set.
● Light will turn off automatically at dawn, and return to 3 H mode at dusk.
3. 6H MODE (nighttime operation only)
● At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%
~50% brightness) automatically after 6 hours. The light will turn to high-level brightness (100% brightness) when
motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light
will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set
● Light will turn off automatically at dawn, and return to 6 H mode at dusk.
4. 0 MODE (nighttime operation only)
● The light will turn to low level brightness (0%~50% brightness) at dusk. The light will turn to high-level brightness
(100% brightness) when motion is detected, and stay on as long as the motion is continuing. When motion is no
longer detected, the light will remain on for the predetermined time you set (5~180 seconds), and then revert to
low level brightness you set.
● Light will turn off automatically at dawn, and return to 0 H mode at dusk.
Turn off the power at fuse or circuit box.
Turn on the power at fuse or circuit box.
