background image

T099 / T0100 --- Page 5 / 5

Assembly Kit

5076MM 

(1 SET)

The following parts are available for re-order if damaged or missing.

Troubleshooting

---The light does not come on at all:

1. Make sure the wall switch and circuit breaker are on.

2. Make sure the wiring is correct.

3. Cover the sensor with dark color cloth to verify that the ambient light level is not too high.

---In TEST mode, the light stays on over 5 seconds after motion is no longer detected:

1. Cover the sensor with a dark color cloth to verify that motion is not detected.

2. The TEST mode may have expired. If you want to reactivate the TEST mode, reboot the power

---In AUTO Mode, the light stays on during the day:

1. The light may be in TEST mode. Stay out of the detection range for 5 minutes, which will allow conversion to 

    AUTO mode.

---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours after dusk:

1. Make sure there has not been an interruption in the electrical power, i.e. the wall switch has not been switched off 

    and turned back on at some point or the circuit breaker had not shut down. 

---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes:

1. Make sure there is no movement that could be picked up by the sensor.

2. Adjust the delay time knob counterclockwise to reduce the delay shut-off time.

---In Manual override, the light stays on after dawn:

1. The ambient light level may be too low due to overcast skies.

Mounting Screw (A)

Mounting Screw (B)

Decorative cover (F)

Mounting Bracket Screw (D)

Fixture Mounting Screw (G)

Mounting Strap (E)

Mounting Screw (C)

Wire Nut (H)

140919

A: 10-1/8"
B: 6-1/2"
C: 6"

Summary of Contents for T0099






Reviews: