background image

T0099 / T0100 --- Page 1 / 5

Important to Know:

1. If you are not familiar with state and local electrical

  codes, it is recommended that you consult with a

  qualified electrician.

2. This fixture requires a 120 VAC, 60 Hz power

  source. 

3. For general safety and to avoid any possible 

  damage to the sensor, be sure the power is

  switched "off" before adjustment.

Maximum Wattage: 25.5 W

Working Temperature Range: -4

0

F ~ 113

0

F

ASSEMBLY  AND  INSTALLATION 

                INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

               2. READ AND SAVE THESE INSTRUCTIONS.

T0099 / T0100

Features:

1. Energy saving LED fixture.

2. Motion sensor: turns light ON automatically when 

    motion is detected and turns light OFF automatically 

    when motion stops.

3. Photocell keeps the light OFF during daylight hours.

4. When in manual override mode, use wall switch 

    to keep the light ON during the night.

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.

Note: Fixture can be wall mounted or eave mounted. 

Wall Mounted 

Eave Mounted

Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)

Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for 

proper operation and to avoid the risk of electrical shock.

For eave mounted only:

Swing the sensor head towards the mounting bracket.

Rotate the sensor head clockwise 180˚ so the controls face down.

Controls

Mounting Bracket

Controls

Controls

Hardware Package (included):

Mounting Screw (A)

Mounting Screw (B)

Decorative cover (F)

Mounting Bracket Screw (D)

Fixture Mounting Screw (G)

Mounting Strap (E)

Mounting Screw (C)

Wire Nut (H)

140919

Summary of Contents for T0099






Reviews: