background image

Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate.

Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK. For your nearest Service Agent please call VAX Care.

EEC STATEMENT OF COMPLIANCE

Manufacturer/EEC importer: V

AX Limited, hereby on our own r

esponsibility declare that the pr

oduct

V-027x Rapide Ultra is manufactur

ed in compliance with the following:

Safety:

73/23/EEC Low Voltage Dir

ective as modified by 93/68/EEC 

EMC:

89/336/EEC Electromagnetic compatibility Dir

ective as modified by 93/68/EEC

Waste electrical pr

oducts should not be disposed of with household waste. Please recycle 

wher

e facilities exist. Check with your Local Authority or retailer for r

ecycling advice.

Vax Ltd., Kingswood Road, Hampton Lovett, Dr

oitwich, Wor

cestershire WR9 0QH, UK

email: [email protected] - website: www

.vax.co.uk

Easy Guide

VAX CARELINE 0870 6061248

Please read carefully before using the carpet washer.
Always fully extend the mains cable before use.
Please retain these instructions for future reference.

VAX Model Number: V-027x

I n s t r u c t i o n   M a n u a l

V-027X User Guide  7/9/06  15:04  Page 16

Summary of Contents for Rapide XL Ultra V-027X
















Reviews: