Vax 88000 User Manual Download Page 15 | Manualshive

Page: 15 / 16

Vax 88000 User Manual Download Page 15

www.vax.com.au

14

Other Information

Vax Service & Help

Vax Careline:

Australia

1300 361 505

New Zealand 0800 800 900

Monday–Friday

8.30am to 5.00pm

If you have queries or concerns about using your Vax, call the Vax Careline. Calls are charged
at the standard local rate. Please make a note of the serial number and model number of the
vacuum cleaner before calling.

For the nearest Service Agent, please call the Vax Customer Careline or visit

www.vax.com.au

Technical Specification

Voltage:

220-240V ~50Hz

Wattage:

600W

Capacity:

Clean water tank: 3.5 Litres

Dirty water tank: 2 Litres

Cord length: 7.5m

Weight:

7.5kg

Filter:

Float chamber filter

Subject to technical change without notice.

Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the Rapide
series is manufactured in compliance with the following Directives:

Safety:

2006/95/EC Low Voltage Directive

EMC:

2004/108/EC Electromagnetic Compatibility Directive

Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.

N197

Double

Insulated

Indoor

Use

Read

Instructions

«
...
13
14
15
16
»

Summary of Contents for 88000

















Reviews:

No comments