background image

EN

TroubleshooTing guide  

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

ProBleM

PoSSiBle cauSe

Solution

Vehicle does  

not operate

 

»

Battery not charged or connected

 

»

ESC switch not ON

 

»

Transmitter not ON or low battery

 

»

Charge battery/connect

 

»

Turn ON ESC switch

 

»

Turn ON/replace batteries

Motor runs but 

rear wheels  

don’t move

 

»

Pinion not meshing with spur gear

 

»

Pinion spinning on motor shaft

 

»

Slipper too loose

 

»

Transmission gears stripped

 

»

Drive pin broken

 

»

Adjust pinion/spur mesh

 

»

Replace pinion gear on motor

 

»

Check and adjust slipper

 

»

Replace transmission gears

 

»

Check and replace drive pin

Steering does  

not work

 

»

Servo plug not in receiver properly

 

»

Servo gears or motor damaged 

 

»

Check if connected/all the way

 

»

Replace or repair servo

Won’t turn in  

one direction

 

»

Servo gears damaged

 

»

Replace servo

Motor does  

not run 

 

»

Motor plugs loose

 

»

Motor wire broken

 

»

ESC damaged

 

»

Plug in completely

 

»

Repair or replace as needed

 

»

Contact Horizon Hobby Product Support

ESC gets hot

 

»

Motor over-geared

 

»

Driveline bound up

 

»

Use smaller pinion or larger spur gear on motor

 

»

Check wheels, suspension and transmission for binding

Poor run time  

and/or sluggish 

acceleration

 

»

Battery not fully charged

 

»

Charger not allowing full charge

 

»

Slipper slipping too much 

 

»

Motor worn out

 

»

Driveline bound up

 

»

Recharge battery

 

»

Try another charger

 

»

Check/adjust slipper

 

»

Replace motor

 

»

Check wheels, transmission for binding

Poor range  

and/or glitching

 

»

Transmitter batteries low

 

»

Vehicle battery low

 

»

Loose plugs or wires 

 

»

Check and replace

 

»

Recharge or replace

 

»

Check all wire connections and plugs

Slipper won’t 

adjust

 

»

Drive pin missing in shaft

 

»

Spur gear face worn out

 

»

Replace drive pin

 

»

Replace spur gear and adjust slipper

Summary of Contents for glamis Fear





















Reviews: