manualshive.com logo in svg

VAT LINVAT 070 Series, Installation, Operating, & Maintenance Instructions

Share
Download
VAT LINVAT 070 Series Installation, Operating, & Maintenance Instructions Download Page 18

MAINTENANCE 

Series 07

 

18/27 

Edition 2020-05-07 

891111EB.DOCX

 

6.3 

Replacement of gate 

 

 

NOTICE 

Wrong tightening torque 

Door body and screws may get damaged. 

Use tightening torque according to size of the screws. 

 

 

 

NOTICE 

Contamination 

Product may get contaminated. 

Always wear cleanroom gloves when handling the product. 

 

 

 

NOTICE 

Inappropriate tools 

Sealing surfaces may get damaged. 

Do not use sharp-edged tools. 

 
 

1.  Vent chambers. 

2.  Open the door. 

3.  Disconnect electrical power supply. 

4.  Disconnect compressed air supply. 

5.  Loosen the screw for the gate (2), use convenience tool (1), see «Figure 6-2» on page 

19. 

6.  Grasp the gate (2), by using the convenience tool (1) into the M8 thread, see «Figure 

6-2» on page 19. 

7.  Remove the gate (2) carefully, if necessary wiggle gently, use convenience tool (1), 

see «Figure 6-2» on page 19. 

 

Summary of Contents for LINVAT 070 Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands