VAT 64.1 Series Installation, Operating And Maintenance Instructions Download Page 12

 

ce

rti

fied

 QM-Sys

tem

g

ep

rüfte

s Q M-S

ys

te

m

ISO 9001

EN 29001

 

Installation, Operating, and Maintenance Instructions 

Series 64.1

 

 

 

 

 

VAT Vakuumventile AG, CH-9469 Haag, Schweiz 

Tel ++41 81 771 61 61   Fax ++41 81 771 48 30   Email [email protected]   http://www.vatvalve.com

 

283681EB

 

2011-03-18 

12/19 

 

 

Problem 

Recommendation 

RS485 interface installed: 
Controller does not respond to 
RS485 commands 

-  Verify settings of the switch S1 on the RS485C interface are correct 
-   Confirm that RS485C interface is installed correctly 
  ‘RS485’ is displayed on the LCD display during start-up  
-  Confirm that PM controller is in REMOTE 
-  Logic inputs on RS485 interface override RS485 commands 

RS485 interface installed: 
Controller responds with error message 

-  Wrong command or transmission error, see chapter ‚9.2 RS485 Interface‘ 

 
 
 

7 Repairs 

Contact VAT for repair. Please check first  the fabrication No. 641P . - . . . . . - . . . .  - . . . .) marked on the rear panel of the 
PM controller.  Your VAT representative will discuss with you how the repair can be carried out best. 
 
 
 

8 Warranty 

Each product sold by VAT Vakuumventile AG (VAT) is warranted to be free from the manufacturing defects that adversely 
affect the normal functioning thereof during the one-year period immediately following delivery thereof by VAT, provided 
that the same is properly operated under conditions of normal use and that regular, periodic maintenance and service is 
performed or replacements made, in accordance with the instructions provided by VAT. The foregoing warranty shall not 
apply to any product or component that has been repaired or altered by anyone other than an authorized VAT 
representative or that has been subject to improper installation or abuse, misuse, negligence or accident. VAT shall not be 
liable for any damage, loss, or expense, whether consequential, special, incidental, direct or otherwise, caused by, arising 
out of or connected with the manufacture, delivery (including any delay in or failure to deliver), packaging, storage or use of 
any product sold or delivered by VAT shall fail to conform to the foregoing warranty or to the description thereof contained 
herein, the purchaser thereof, as its exclusive remedy, shall upon prompt notice to VAT of any such defect or failure and 
upon the return of the product, part or component in question to VAT at its factory, with transportation charges prepaid, and 
upon VAT's inspection confirming the existence of any defect inconsistent with said warranty or any such failure, be entitled 
to have such defect or failure cured at VAT's factory and at no charge therefor, by replacement or repair of said product, as 
VAT may elect. VAT MAKES NO WARRANTY OR REPRESENTATION OF ANY KIND, EXPRESS OR IMPLIED, 
(INCLUDING NO WARRANTY OR MERCHANTABILITY), EXCEPT FOR THE FOREGOING WARRANTY AND THE 
WARRANTY THAT EACH PRODUCT SHALL CONFORM TO THE DESCRIPTION THEREOF CONTAINED HEREIN, and 
no warranty shall be implied by law. 
Furthermore, the «Terms of sale» at the back of the price list are applicable. 
 

Summary of Contents for 64.1 Series





















Reviews: