manualshive.com logo in svg

VASTEX DB-30, Assembly & Operating Manual, Page: 11 / 12

Share
Download
VASTEX DB-30 Assembly & Operating Manual Download Page 11

Vastex International, Inc. 
1032 N. Irving St.  
Allentown, Pa. 18109 USA 
Phone# 610 434-6004   
Fax# 610 434-6607  
Web Site  www.vastex.com 
E-Mail [email protected] 

Installation: Conveyor Belt Covers 

DB Series and EC-I Series Dryers 

Doc. # 01-01-014 

Tools Required: 1/4” Nut Driver, or 1/4” socket and ratchet 

Package Contents: 
(3) Belt Covers (actual covers may differ from pictures) 
(1) Chain Guard 
(8) Sheet Metal Screws 

Conveyor Front 

Belt Cover 

(2) Screws 

Belt Cover 

Conveyor Rear 

(2) Screws 

Chain Guard 

Vastex International, Inc. 
1032 N. Irving St.  
Allentown, Pa. 18109 USA 
Phone# 610 434-6004   
Fax# 610 434-6607  
Web Site  www.vastex.com 
E-Mail [email protected] 

Installation: Conveyor Belt Covers 

DB Series and EC-I Series Dryers 

Doc. # 01-01-014 

Tools Required: 1/4” Nut Driver, or 1/4” socket and ratchet 

Package Contents: 
(3) Belt Covers (actual covers may differ from pictures) 
(1) Chain Guard 
(8) Sheet Metal Screws 

Conveyor Front 

Belt Cover 

(2) Screws 

Belt Cover 

Conveyor Rear 

(2) Screws 

Chain Guard 

11

Summary of Contents for DB-30













Reviews:

No comments