Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • [email protected]
DocID: 507634_04.05.2021
EN
Quick start guide
This quick start guide contains important information on the safe operation of the
product. Read and follow the safety advice and instructions given. Retain the quick
start guide for future reference. If you pass the product on to others please include
this quick start guide.
GLC-1 Go Light Creator
Safety instructions
Intended use
This device is intended to be used as a portable video light. Any other use or use
under other operating conditions is considered to be improper and may result in
personal injury or property damage. No liability will be assumed for damages resul-
ting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are
not within reach of babies and young children. Choking hazard! Ensure
that children do not detach any small parts from the product. They could
swallow the pieces and choke!
Incorrect handling of lithium batteries can result in injury
• In the event of a short circuit, overheating or mechanical damage, lithium batteries
can cause severe injuries.
• When handled correctly and appropriately lithium batteries pose no risk.
• Store lithium batteries in a cool, dry place, ideally in the original packaging.
• Store lithium batteries away from heat sources (e.g. radiators or sunlight). Lithium
batteries are hermetically sealed. Never attempt to open a lithium battery.
• If the battery housing is damaged small amounts of the electrolyte may leak out. If
this should happen, seal the lithium battery in airtight packaging and wipe up the
traces of electrolyte using absorbent paper towels. You must wear protective rub-
ber gloves when doing so. Clean your hands and the affected surface thoroughly
with cold water.
• Never attempt to recharge non-rechargeable lithium batteries. When charging lit-
hium batteries you must use a suitable charging device intended for the purpose.
• Before disposing of the device remove the lithium batteries. Protect used lithium
batteries against potential short circuits, e.g. by covering the poles with adhesive
tape.
• Only use powder extinguishers or other suitable extinguishing agents to extingu-
ish a burning lithium battery.
Possible damage to lithium-ion batteries through incorrect storage
By deep discharge, lithium-ion batteries can be permanently damaged or lose
some of their capacity.
Before long breaks, charge the batteries to around 50 % of their capacity and then
switch off the device. Store the device at room temperature or cooler in an environ-
ment as dry as possible. If the batteries are stored for a longer period, recharge
them to 50 % every three months.
Fully charge the batteries only shortly before use at room temperature.
Where to use the product
Never use the product
• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet
General handling
• To prevent damage, never use force when operating the switches and controls.
• Never immerse the appliance in water. Just wipe it with a clean dry cloth. Do not
use liquid cleaners such as benzene, thinners or flammable cleaning agents.
Operating elements
Front side
1. Front LED panel
2. Side LED panels
3. Openings for folding out the side LED
panels
4. Switch for selecting the lighting configu-
ration
5. On / off switch
6. Charge indicator
7. Infrared sensor
Bottom side
8. USB-C port for charging the internal
battery
9. 1/4" thread for tripod mounting
LED panels fully unfolded
LED panels unfolded to 90°
Features
• Portable folding video light
• Adjustable colour temperature from 3000 K to 6000 K.
• High CRI of 95
• Remote control via IR to control brightness and colour temperature
• 1/4" thread on the bottom for tripod mounting
• Built-in battery with a runtime of up to 16 hours at the lowest brightness and up
to four hours at 100% brightness
Remote control
10. Infrared signal transmitter
11. On / off switch
12. Switch for selecting the light panels
13. Switch for adjusting the brightness
14. Switch for setting the colour temperature
