background image

 

POWX1730 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

8

 

www.varo.com 

8.4 

Storage 

I mportant! Pull the mains plug out of the socket and ventilate the appliance 
and all connected pneumatic tools. Switch off the compressor and make 
sure that it is secured in such a way that it cannot be started up again by 
any unauthorized person. 

Important! Store the compressor only in a dry location which is not 
accessible to unauthorized persons. Always store upright, never tilted! 

9  TECHNICAL DATA 

Type 

POWX1730 

Rated voltage

 

230V

 

Rated frequency 

50Hz 

Rated Power 

1100W / 1,5 pk 

Rotation speed 

3400 min

-1

 

Rated Pressure 

8 bar / 116PSI 

Tank capacity 

24 l 

Air debit (capacity) 

180 l/min 

Weight 

20 kg 

10 NOISE 

Noise emission values measured according to relevant standard. (K=3) 
Acoustic pressure level LpA 

77 dB(A) 

Acoustic power level LwA 

97 dB(A) 

ATTENTION! Wear hearing protection when sound pressure is  
over 85 dB(A). 

11 POSSIBLE FAULTS AND RELATED PERMITTED REMEDIES 

FAULT 

CAUSE 

REMEDY 

The compressor 
does not start 

1. No supply voltage 

1. Check the supply voltage, the power 
plug and the socket-outlet. 

2. Insufficient supply 
voltage 

2. Make sure that the extension cable is 
not too long. Use an extension cable with 
large enough wires. 

3. Outside temperature 
is too low 

3. Never operate with an outside 
temperature of below +5°C. 

4. Motor is overheated 

4. Allow the motor to cool down. If 
necessary, remedy the cause of the 
overheating. 

The compressor 
starts but there is 
no pressure 

1. Leak in the non-return 
valve 

1. Replace the non-return valve 

2. The seals are 
damaged. 

2. Check the seals and have any 
damaged seals replaced by a service 
center 

3. The drainage screw 

3. Tighten the screw by hand. Check the 

Summary of Contents for POWERPLUS POWX1730











Reviews: