background image

 

POWEG8010 

EN

 

Copyright © 2018 VARO 

P a g e

 | 

4

 

www.varo.com 

4  SYMBOLS 

In this manual and/or on the machine the following symbols are used: 

 

Read the manual before 
using the machine 

 

Wear sturdy shoes with antiskid 
soles ! 

 

Denotes risk of personal 
injury or damage to the tool. 

 

Wear approved hearing 
protection and safety glasses 

 

In accordance with essential 
applicable safety standards 
of European directives 

 

Wear good and sturdy gloves! 

 

Keep a minimum distance of 
15m between the machine 
and third parties during use 

 

WATCH OUT Fire hazard! 
Gasoline and vapors are easily 
inflammable!  

 

Watch out for particles 
generated by the cutting 
installation 

 

The exhaust fumes are toxic and 
can cause suphocation ! 

5  SPECIFIC SAFETY INSTRUCTIONS FOR BUSH CUTTERS 

 

FOLLOW ALL WARNINGS and instructions regarding operation and blade installation. 

 

BLADE CAN RECOIL VIOLENTLY FROM MATERIAL IT CANNOT CUT 

– Blade can 

cause you to lose arms or legs.  Keep people and animals 50 feet (15 meters) away in all 
directions. If blade contacts foreign objects during operation, turn off engine and allow  
blade to come to a halt. Then check blade for damage. Always discard blade if it is warped 
or cracked. 

 

INSPECT YOUR TRIMMER AND ATTACHMENTS BEFORE USE - Never use unless all 
blade attachment hardware has been properly installed. 

 

BLADE COASTS AFTER THROTTLE IS RELEASED - A coasting blade can injure you or 
bystanders. Before servicing the blade, always turn off engine, and be sure coasting blade 
has stopped.  

 

WARNING DO NOT USE ANY OTHER FUEL than that recommended in your manual. 
Always follow instructions in the Fuel and Lubrication section of this manual. Never use 
petrol unless it is properly mixed with 2-cycle engine lubricant. Permanent damage to 
e

ngine will result, voiding manufacturer’s warranty. 

 

DO NOT SMOKE while refueling or operating equipment. 

 

DO NOT OPERATE UNIT WITHOUT A SILENCER and properly installed silencer shield. 

 

DO NOT TOUCH or let your hands or body come in contact with a hot silencer or sparking 
plug wire. 

 

DO NOT OPERATE UNIT IN AWKWARD POSITIONS, off balance, with outstretched 
arms, or with one hand. Always use two hands when operating unit, with thumbs and 
fingers encircling the handles. 

 

DO NOT RAISE STRINGHEAD above ground level while unit is operating. Injury to 
operator could result. 

 

DO NOT USE UNIT FOR ANY PURPOSES OTHER than trimming lawn or garden areas. 

 

DO NOT OPERATE UNIT FOR PROLONGED PERIODS. Rest periodically. 

 

DO NOT OPERATE UNIT WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. 

 

DO NOT OPERATE UNIT UNLESS DEBRIS SHIELD AND/OR GUARD IS INSTALLED 
AND IN GOOD CONDITION. 

Summary of Contents for POWERPLUS POWEG8010














Reviews: