RBS-700D
3.
On the chassis
4
, using two M8x16 bolts with collar
8
, attach the mud flap
11
– notch on the bracket shall be oriented
towards the notch in the machine's chassis
12
.
4.
Turn the machine 180° and place it on the lower support disc.
5.
Place the plastic drum cover
13
on the top edge of the chassis moulding
4
. At the back the cover must extend beyond the
steel-sheet bracket of the mud flaps
14
.
6.
Place the handle
15
on the front raised part of the plastic cover. Insert two M6x16 hexagonal head bolts
16
into the feet in the
lower part of the handle and thread the M6 nuts
17
on.
Do not tighten!
7.
Insert two M6x16 button headed bolts and square
18
into the square holes, fit the large washers 6.6mm
10
and thread on
the M6 safety nuts
17
.
Do not tighten!
8.
Mount four M6x16 bolts
16
with large washers 6.6mm
10
and mount the M6 safety nuts
17
.
Do not tighten!
9.
In the vertical rear part of the plastic cover
13
insert both outside mud flaps
19
between the plastic drum cover
13
and the
steel sheet mud flap bracket
14
. Bolt the plastic cover
13
, mud flaps
19
and the steel mud flap bracket
14
together using
the M6x16
16
bolts with large washers 6.6mm
10
and the M6 safety nuts
17
.
10. On the outside of the plastic cover
13
use M6x16 bolts
14
with large washers 6.6mm
10
, insert large 6.6mm washer
10
under the M6 safety nuts
17
.
11. Now tighten the four bolts attaching the plastic cover to the chassis, which you assembled in point 8..
12. Then tighten the M6x16 handle bolts
15
with hexagonal head, first two M6x16 bolts with hexagonal head
16
near the bottom
feet
, then the M6 safety nuts
17
on the bottom side of the plastic cover near the handle's top edge.
13. If you will not be ataching the adaptor
RBS-700D
to the multifunctional carrier
RAPTOR Hydro
, slide the steel V-belt cover
20
with the bayonet grooves on four bolts
21
in the back of the moulding of the machine frame and tighten the bolts –
wrench or socket 10 mm.
Two M10 bolts with collar, supplied in a bag with the manuals, are designed to attach the adaptor to the multifunctional
carrier. As the carrier is fitted with one set of bolts from the factory, store these spare botls in case of loss or damage.
2.4.2 Attaching and removing the adaptor
Never attach or remove the adaptor from the multifunctional carrier on a slope! There is a risk of loss of the
machine's and operator's stability. Always seek the most level surface.
When attaching or removing the adaptor, all other people (especially children) and animals must stay outside the
machine's work area. The operator may only continue working after they reach a safe distance.
The tools – both active and passive – carried in the front of the machine are connected through four attachment points with M10 internal
threads that are placed in the side-walls of the lower frame of the multifunctional carrier –
RAPTOR Hydro
-
1
and
2
on
Fig. 5
on
The rear attachment points
2
2 serve to direct the adaptors to the correct position in relation the drive pulley of the adaptor's drive
3
.
Collar screws
4
are part of the
RAPTOR Hydro
carrier and remain attached in the carrier frame when disconnecting the adaptor.
Front attachment points
1
serve to firmly fix the tool to the carrier. Two collar screws are part of the purchased
RAPTOR Hydro
carrier
. When disconnecting the tool from the carrier, they are entirely unscrewed and taken out.
For tightening the attachment screws, use a bent ratchet wrench with 3/8“ square drive and 12-point socket 15 mm –
Fig.
. Select the ratchet wrench with as low head as possible.
We recommend to lubricate the threads in the frame of the carrier with a lubricant that prevents the threads from
seizing and protects against corrosion (lubricants with addition of the graphite and copper used to lubricate moving
parts of the disc brakes – e.g. LOCTITE 8007).
2.4.2.1 Attaching the adaptor
Proceed with caution when changing attachments. When the engine is turned off, the exhaust silencer remains
hot - risk of burns.
The rear part of the adaptor's plastic cover is heated during the operation by hot air from the engine - therefore
the heat shield can be very hot - risk of burns.
You can find the instruction video on the adaptor replacement on our web pages on the product's tab.
Set of figures
Fig. 6
. The number in the corner matches the numbering in the text, however some numbers do
not have a figure.
1.
Close the fuel supply to the engine – the fuel valve button position
OFF
and set the accelerator lever to the
STOP
position.
2.
Tilt the machine back on the handle bars and lean the hinge on a support.
If you are connecting the adaptor on asphalt, concrete or other substantially solid ground, we recommend to support
the hinge with e.g. cloth, piece of carton or other suitable soft material. You will prevent any damage of the machine's
surface finish.
3.
Loosen the M10x20 bolts in the rear attachment points on the frame of the multifunctional carrier by 2-3 turns.
39
Additional two spare screws are part of the supplied tool.
21
re
vi
ze
0
2/
20
18
Summary of Contents for RBS-700D
