background image

VARI

LITE - VL6000 B

EAM

 L

UMINAIRE

 U

SER

S

 M

ANUAL

40

27 April 2017

02.9708.0002

Notes:

Default Values: *Denotes recommended console default settings.

16
17

Gobo 1 Rot/Index

High Byte

Low Byte

0 - 65535

0 - 100%

0

16-bit control of index and rotation of gobo wheel 1.

0-32756 = Rotate Fast to Slow
32757-32780 = Rotation STOP
32781-65535 = Rotate Slow to Fast

18

Gobo Wheel 1

Control

0 - 255

0 - 100%

0

Used as a control channel for different movement options for Gobo 
Wheel 1 (Channel 15) 

0-5 = Gobo Selection using shortest (quickest) path.
6-10 = Gobo Selection using normal (longest) path.
11-20 = Reserved Values
21-50 = Wheel Spin Forward (Fast to Slow)
51-60 = Wheel Spin STOP
61-90 = Wheel Spin Reverse (Slow to Fast)
91-120 = Gobo Shake Quickest Path (Slow to Fast)
121-150 = Gobo Shake Normal Path (Slow to Fast)
151-180 = Gobo Twist Quickest Path (Slow to Fast)
181-210 = Gobo Twist Normal Path (Slow to Fast)
211-255 = Reserved Values

19

Iris

0 - 255

0 - 100%

0

Controls Iris mechanism from open (DMX 0) to Full (DMX 255)

20

Frost

0 - 255

0 - 100%

0

Controls Frost mechanism from open (DMX 0) to Full (DMX 255)

21

Strobe Speed

0 - 255

0 - 100%

0

Controls Strobe rate from slowest (DMX 0) to fastest (DMX 255)

22

Strobe Control

0 - 255

0 - 100%

0

Control Channel for strobing functions
0-5 = Open
6-10 = Closed
11-15 = Normal Strobe
16-20 = Random Strobe
21-25 = Random Sync
26-255 = Reserved Values

23

Luminaire

Control

0 - 255

0 - 100%

0

Control Channel used for full fixture settings, lamp controls, and miscel-
laneous modes. Set descreet value of desired effect, wait >3 seconds, 
then set value to 0 (Idle).

0-5 = Idle (Default)
6-10 = Full Luminaire ReCal-Also Used to Wake fixture up from shut-
down
11-15 = Lamp ON
16-20 = Lamp OFF
21-25 = Fixture Shutdown
26-30 = Display-Menu ON
31-35 = Display-Menu OFF
36-40 = ReCal Position
41-45 = ReCal Color
46-50 = ReCal Gobo
51-55 = ReCal Beam
56-60 = ReCal Dimmer/Strobe
61-65 = Reset Fixture to Defaults
66-70 = Full Luminaire Reboot.  This command will douse lamp and 
reset all processors in fixture, then ReCal all parameters.  
71-75 = Fixture Status On/Off.  This command will enable the display to
show fixture status for 5 min.  After this time, displays will return to 
default configuration.  Repeating the command in less than 5 minutes 
will behave as a toggle.
76-80 = Dimmer Snap Off (default)
81-85 = Dimmer Snap On
86-90 = Pan / Tilt Normal (Default)
91-95 = Pan / Tilt Fast
95-255 = Reserved Values

Table 2: VL6000 Beam Luminaire 16-Bit DMX Channel Mapping

DMX 

Channel

Parameters

Range

(DMX)

Range

(%)

Default 

Value*

Description / Operation

Summary of Contents for VL6000 Beam Luminaire








































































































Reviews: