background image

 

 

 

VLC5501 Vapormatic Immobiliser Installation Manual                                                    

4 of 21

 

 

Product warranty and registration:

 

Warranty of this product is for 12 months. If you register this product on line, Vapormatic 
will give a further 12 months warranty free, giving 24 months in total. 

 

To register this product please go to: 

 

www.vapormatic.com/vehiclesecurity

 

 

 

Safety instructions:

 

 

 

Please read this manual carefully before installation. 

 

 

This security system should be installed by a qualified Agricultural 
Technician. If you have any concerns with fitting this immobiliser, you 
should seek professional advice by taking it to your local authorised 
vehicle dealer. 

 

 

The vehicles battery should be disconnected during this installation. 

 

 

An incorrect installation could damage the security system and/or 
vehicles electronics. 

 

 

The keypad and both immobiliser blockers must be protected by the fuses 
supplied and all components firmly fastened in to their location. 

 

 

All interconnecting wiring connections shall confirm to one or more of the 
following methods:- 

 

Insulated crimp type connectors 

 

Vehicle manufacturers recommended method of termination 

 

Summary of Contents for VLC5501






















Reviews: