TOOLS USE AND CARE
1.
Use clamps or other practical means to secure and support the workpiece to a sta-
ble platform.
Holding the work by hand or against your body is unstable and may lead to loss of con-
trol.
2.
Do not force tool. Use the correct tool for your application.
The correct tool will do the job
better and safer at the rate for which it is designed.
3.
Do not use tool if switch does not turn it ON or OFF.
A tool that cannot be controlled with
the switch is dangerous and must be repaired.
4.
Disconnect the plug from the power source before making any adjustments, chang-
ing accessories, or storing the tool.
Such preventive safety measures reduce the risk of starting
the tool accidentally.
5.
Store idle tools out of reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool.
Power tools are dangerous in the
hands of untrained users.
6.
Keep cutting tools sharp and clean.
Properly maintained tools, with sharp cutting edges are
less likely to bind and are easier to control.
7.
Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts, and any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using.
Many accidents are caused by poorly maintained tools.
8.
Use the power tool, accessories and tool bits etc., in accordance with these instruc-
tions and in the manner intended for the particular type of power tool, taking into
account the working conditions and the work to be performed.
Use of the power tool for
operations different from those intended could result in a hazardous situation.
SERVICE
1.
Tool service must be performed only by qualified repair personnel
. Service or mainte-
nance performed by unqualified personnel may result in a risk of injury.
2.
When servicing a tool, use only identical replacement parts.
Follow instructions in the
Maintenance Section of this manual. Use of unauthorized parts or failure to follow Maintenance
Instructions may create a risk of electric shock or injury.
WORK AREA
1.
Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust.
Power tools create sparks which may ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions
can cause you to lose control.
ELECTRICAL SAFETY
1. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in
any way. Double insulation eliminates the need for the three wire grounded power cord and grounded
power supply system.
2.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators
. There is an increased risk of electric shock if your body is grounded.
3.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will
increase the risk of electric shock.
4.
Do not abuse the cord. Never use the cord to carry the tool or pull the plug from an
outlet. Keep cord away from heat, oil, sharp edges or moving parts.
Replace damaged
cords immediately. Damaged cords increase the risk of electric shock.
5.
When operating a power tool outside, use an outdoor extension cord marked “W-A”
or “W
”. These cords are rated for outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
1.
Stay alert, watch what you are doing, and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication.
A moment of inattention while operating power tools may result in serious personal injury.
2.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be
caught in moving parts.
3.
Avoid accidental starting. Be sure switch is OFF before plugging in.
Carrying tools with
your finger on the switch or plugging in tools that have the switch ON invites accidents.
4.
Remove adjusting keys or wrenches before turning the tool ON.
A wrench or a key that is
left attached to a rotating part of the tool may result in personal injury.
5.
Do not overreach. Keep proper footing and balance at all times.
Proper footing and bal-
ance enable better control of the tool in unexpected situations.
6.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard
hat, or hearing protection must be used for appropriate conditions.
5
4