background image

2

MiniVap

Positioning the MiniVap Unit

DOs

DO mount the unit indoors.

DO  mount  the  unit  close  to  the  steam  nozzle  /  steam  pipe 
position.

DO  ensure  adequate  service  access  to  the  front  of  the  unit 
(min 700mm).

DO  remove  the  cylinder,  if  necessary,  to  access  the  mounting 
holes in the back of the steam section.

DO  use  M6  projecting  type  wall  bolts  or  equivalent  fixings  to 
mount the unit in position.

DO mount unit with a Room Distribution Unit (RDU) so that the 
steam  discharge  is  above  head  height.    (An  RDU  includes  a 
steam nozzle and a small fan with 230Vac motor.)

DON’Ts

DON’T mount the unit outside.

DON’T  install  the  unit  close  to  sources  of  strong  electro-
magnetic  emissions  eg  variable  speed  lift  motor  drives,  KVA 
transformers, etc.

DON’T mount unit in an unventilated enclosure.

DON’T mount in a position requiring ladder access to the unit.

DON’T  install  the  unit  behind  a  false  ceiling  or  other  situation 
where  an  unusual  malfunction  (eg  water  leak)  would  cause 
damage.

DON’T install the unit in an area which will be hosed down.

DON’T  install  the  unit  where  the  ambient  air  temperature  can 
exceed 35°C.

DON’T mount the unit inside a cold-room or other  place  where 
temperature  and  humidity  conditions  can  cause  condensation 
on electrical components.

DON’T mount the unit where  the sound of a  contactor opening 
/  closing  and  water  flow  in  a  pipe  would  be  unacceptable  eg
libraries, private apartments, etc.

Summary of Contents for MiniVap LMV2











Reviews: