background image

                                                      SBC-RK35M Boards User’s Manual   

All rights reserved                                                                                                Page 17, Total 18 

5

 

Tips 

  Waste Disposal 

It is recommended to disassemble the device before abandoning it in conformity with local regulations. 

Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do 
not throw batteries into fire (explosive) or put in common waste canister. Products or product packages with 
the sign of “explosive” should not be disposed like household waste but delivered to specialized electrical

electronic waste recycling/disposal center. Proper disposal of this sort of waste helps avoiding harm and 
adverse effect upon surroundings and people’s health. Please contact local organizations or 
recycling/disposal center for more recycling/disposal methods of related products.   

Comply with the following safety tips: 

  Do not use in combustible and explosive environment 

 
Keep away from combustible and explosive environment for fear of danger.   

  Keep away from all energized circuits.   

Operators should not remove enclosure from the device. Only the group or person with factory certification 

is permitted to open the enclosure to adjust and replace the structure and components of the device. Do not 
change components unless the power cord is removed. In some cases, the device may still have residual 
voltage even if the power cord is removed. Therefore, it is a must to remove and fully discharge the device 
before contact so as to avoid injury.   

  Unauthorized changes to this product or its components are prohibited.     

In the aim of avoiding accidents as far as possible, it is not allowed to replace the system or change 

components unless with permission and certification. Please contact the technical department of Vantron or 
local branches for help.   

 

  Pay attention to caution signs.   

Caution signs in this manual remind of possible danger. Please comply with relevant safety tips below each 

sign. Meanwhile, you should strictly conform to all safety tips for operation environment.   

 

  Notice 

Considering that reasonable efforts have been made to assure accuracy of this manual, Vantron assumes 

no responsibility of possible missing contents and information, errors in contents, citations, examples, and 
source programs.   

Vantron reserves the right to make necessary changes to this manual without prior notice. No part of this 

manual may be reprinted or publicly released in forms of photocopy, tape, broadcast, e-document, etc.

 

Summary of Contents for SBC-RK35M



















Reviews: