background image

2.) 

Install the limit switch as per detail from page 14.

3.) 

Install the fan support and the fan as per detail from 

page 25.

4.) 

Install the fan powerline prior to the installation of the 

Lyra VR128BN as Per. CAN/CGA 22231/NFPA codes. 

5.) 

Install 

the insert following these steps.

 

A. Remove the screen and door as per page 15.

 

B. Remove the burner tray and the front sliding 

 

     baffle.

 

C. Remove the burner tray / valve.

 

D. Slide the insert shell into the Montigo fireplace. 

 

     sitting on the 1/2” lips.  Ensure the upper down

 

     draft baffle passes through and into the old com

 

     bustion chamber. Front on, the isert should  be

 

     flush with the old Montigo unit.

 

E. Secure the insert with the self tapping screws. 

 

     One in each corner.

 

F. Attach back the insert burner tray, connecting 

 

    the gas, the limitch switch, and the fan.

 

G. Install the glass media or logs as per detail on

 

     page 26.

 

H. Install the door and protection screen as per

 

     detail on page 15.

Figure 24. 

Installing the One piece surround.

Montigo 28 Series 

Reinforcement 

   

Top

Instalation of Reinforcement 

Top into Montigo 28 Series

Installation of Lyra VRI28BN:

1.) 

Install the reinforcement top kit (RIFK) sliding up into 

the Montigo combustion chamber and secure it with the 
self tapping screws into the sides, back, and top.

Installation of One piece Surround 

1.) 

The Faceplate Kit (FPK28) comes with two (2) brackets 

which have to be installed into the Right / Left upper corners 

of existing Montigo 28 Series Model as per. Detail Below:

`   Detail 

1

The Brackets have to be flush with the Fireplace Left / Right 

Wall and upper edge (See Detail 2) and secured with the two 

(2) self tapping screws.

 

           Detail 2 Right upper corner

Fireplace body

Faceplate mount

Bracket, flush to 

the back and side

Flush to the top

Faceplate FPK28

To bottom of the surround clip to the magnets installed on 

the fireplace tray. 

NOTE: After installationensure the distance from the fan hood 

and faceplate is MIN 5/8” gap to ensure proper draft.

Part. No. 

VZB28BN-Man-101817-A

VZB28BN Gas Fireplace

VANOX Fireplace Inc.

Page 17

Summary of Contents for LYRA VZB28BN































Reviews: