Vanguard VP5D Owner'S Operation And Installation Manual Download Page 14

PROPANE/LP GAS HEATERS

14

®

 VP5D AND VP10A

104273

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

Burner(s) does not light after ODS/pilot is lit

Delayed ignition of burner(s)

Burner backfiring during combustion

Burner plaque(s) does not glow

Slight smoke or odor during initial operation

Heater produces a clicking/ticking noise
just after burner is lit or shut off

White powder residue forming within burner
box or on adjacent walls or furniture

REMEDY

1. Clean burner orifice(s) (see Cleaning

and Maintenance, page 12) or replace
burner orifice(s)

2. Replace burner orifice(s)
3. Contact local propane/LP gas company

1. Contact local propane/LP gas company
2. Clean burner orifice(s) (see Cleaning

and Maintenance, page 12) or replace
burner orifice(s)

1. Clean burner orifice(s) (see Cleaning

and Maintenance, page 12) or replace
burner orifice(s)

2. Contact local propane/LP gas company
3. Replace burner
4. Replace gas regulator

1. Replace burner
2. Contact local propane/LP gas company
3. Turn control knob until it locks at de-

sired setting

1. Problem will stop after a few hours of

operation

1. This is common with most heaters. If

noise is excessive, contact qualified ser-
vice person

1. Turn heater off when using furniture

polish, wax, carpet cleaners, or similar
products

POSSIBLE CAUSE

1. Burner orifice(s) is clogged

2. Burner orifice(s) diameter is too small
3. Inlet gas pressure is too low

1. Manifold pressure is too low
2. Burner orifice(s) is clogged

1. Burner orifice(s) is clogged or damaged

2. Inlet gas pressure is too low
3. Burner damaged
4. Gas regulator defective

1. Plaque damaged
2. Inlet gas pressure is too low
3. Control knob set between locked positions

1. Residues from manufacturing processes

1. Metal expanding while heating or con-

tracting while cooling

1. When heated, vapors from furniture pol-

ish, wax, carpet cleaners, etc. turn into
white powder residue

www.desatech.com

Summary of Contents for VP5D





















Reviews: