Vanguard Amity SCIVFB Owner'S Operation And Installation Manual Download Page 25

Page: 25 / 32

104025

TROUBLE-

SHOOTING

Continued

WARNING ICON

G 001

WARNING

If you smell gas

• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas
supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

IMPORTANT:

Operating heater where impurities in air exist may create odors.

Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new
carpet or textiles, etc., create fumes. These fumes may mix with combustion air
and create odors. These odors will disappear over time.

POSSIBLE
CAUSE

1. Metal expanding while

heating or contracting
while cooling

1. Heater burning vapors

from paint, hair spray,
glues, cleaners, chemi-
cals, new carpet, etc. (See

IMPORTANT

statement

above)

2. Gas leak.

See Warning

statement at top of
page

1. Not enough fresh air is

available

2. Low line pressure

3. ODS/pilot is partially

clogged

1. Gas leak.

See Warning

statement at top of
page

2. Control valve defective

1. Foreign matter between

control valve and burner

2. Gas leak.

See Warning

statement at top of
page

OBSERVED
PROBLEM

Heater produces a
clicking/ticking noise
just after burner is lit or
shut off

Heater produces
unwanted odors

Heater shuts off in use
(ODS operates)

Gas odor even when
control knob is in OFF
position

Gas odor during
combustion

REMEDY

1. This is common with

most heaters. If noise is
excessive, contact
qualified service person

1. Open window and

ventilate room. Stop
using odor causing
products while heater is
running

2. Locate and correct all

leaks (see Checking Gas
Connections, page 17)

1. Open window and/or

door for ventilation

2. Contact local

propane/

gas company

3. Clean ODS/pilot (see

Cleaning and Mainte-
nance, page 22)

1. Locate and correct all

leaks (see Checking Gas
Connections, page 17)

2. Replace control valve

1. Take apart gas tubing and

remove foreign matter

2. Locate and correct all

leaks (see Checking Gas
Connections, page 17)

Summary of Contents for Amity SCIVFB

































Search results

Summary of Contents for Amity SCIVFB

Reviews:

Related manuals for Amity SCIVFB

Brands by name

Popular brands

Vanguard Amity SCIVFB, Owner'S Operation And Installation Manual

Search results

Summary of Contents for Amity SCIVFB

Reviews:

Related manuals for Amity SCIVFB

Brands by name

Popular brands