English
– Installation Instructions
WARNING
Before starting to install and work with this device, please read
the
Safety Instructions
.
This device shall only be connected to power supplies compliant to
EN60950-1, chapter 2.5 ("limited power source").
When changing or installing a SPCW130 on the SPC system, ensure that all
anti-static precautions are adhered to while handling connectors, wires,
terminals and PCBs.
EC Declaration of Conformity
Hereby, Vanderbilt International (IRL) Ltd declares that this radio equipment type is
in compliance with all relevant EU Directives for CE marking. From 20/04/2016 it is
in compliance with Directive 2014/30/EU (Electromagnetic Compatibility Directive)
and Directive 2014/35/EU (Low Voltage Directive) . From 13/06/2016 it is also in
compliance with Directive 2014/53/EU (Radio Equipment Directive).
The full text of the EU declaration of conformity is available at
http://pcd.vanderbiltindustries.com/doc/SPC
Introduction to the SPCW130
The SPCW130 provides an interface for 868 MHz wireless detectors. The
SPCW130 incorporates the following elements, as shown in Fig. 1.
The expander should be powered up for at least 30 seconds before performing
any operations.
1.
Front tamper switch
— the expander has a front tamper switch with spring.
When the lid is closed the spring closes the switch.
2.
Tamper by-pass [J1]
— the jumper setting determines the operation of the
tamper. The tamper operation can be overridden by fitting J1.
3.
Buzzer
— the buzzer is activated in order to locate the expander (see
SPC
Configuration Manual
).
4.
Wireless module
— the module provides the wireless interface for
868 MHz devices. Please note that only Intrunet wireless devices can be
enrolled on to this device.
5.
LED
— activated if wireless telegrams are received.
The LED is indication the reception of all wireless telegrams. It is also
indicating the reception of not valid wireless telegrams.
6.
X-BUS status LED
— the LED indicates the status of the X-BUS when the
system is in FULL ENGINEER mode, as shown below:
LED status
Description
Flashes regularly
(once every 1.5 seconds
approx.)
The X-BUS communications status is OK.
Flashes quickly
(once every 0.2 seconds
approx.)
Indicates the last in line expander (excludes star
and multi-drop configuration)
7.
Manual addressing switches
— the switches allow manual setting of the ID of
each expander in the system.
8.
Auxiliary power supply (12 V)
— these are used to power auxiliary devices to a
maximum of 200 mA.
9.
Input power
— the expander requires 12 V DC that can be supplied directly
from the SPC-series controller or from a SPC PSU expander.
10.
X-BUS interface
— the communication bus is used to connect expanders
together on the SPC-series system (see section Wiring the X-BUS interface).
11.
Termination jumper
— this jumper as a default is always fitted, however, when
wiring for Star configuration this fitting should be removed (see section Wiring
the X-BUS interface).
Wiring the X-BUS Interface
The X-BUS interface provides connection of expanders and keypads to the SPC
controller. The X-BUS can be wired in a number of different configurations
depending on the installation requirements.
NOTE:
Maximum system cable length = number of expanders and keypads in the
system x maximum distance for cable type.
Cable type
Distance
CQR standard alarm cable
200 m
UTP category: 5 (solid core)
400 m
Belden 9829
400 m
IYSTY 2 x 2 x 0.6 (min)
400 m
Fig. 2 shows the wiring of the X-BUS to an expander/controller and the following
expander/ controller in Spur configuration. Terminals 3A/3B and 4A/4B are only
used for using a branch wiring technique. If using a Spur configuration, the last
expander is not wired back to the controller.
Fig. 2: Wiring of Expanders
1
SPC controller
2
Previous expander
3
SPCW130
4
Next expander
Please refer to
SPC Configuration Manual
of connected controller for further wiring
instructions, shielding, specifications and limitations.
X-BUS Addressing
For addressing, reconfiguration, device location, monitoring, editing of names, X-
BUS type of communication, failure timer please refer to
SPC Configuration
Manual
.
Appendix
Fig. 3: SPCW130 Enclosure
1
Expander anchor points
2
Wall spacers
3
Cover anchor points
4
Cable grips
5
Mounting holes
6
Cable entry holes
7
Cable ties
8
Cover hooks
Fig. 4: Expander Cover
1
Front tamper guide
2
Cover fixing screws
Technical Data
Operating voltage
9.5
– 14 V DC
Current consumption
60 mA at 12 V DC
Field bus
X-BUS on RS485 (307 kb/s)
Interfaces
X-BUS (In, Out, Branch)
Radio module
Integrated SiWay RF receiver (868 MHz)
Tamper contact
On-board front spring tamper
Operating temperature
-10 to +50 °C
Relative humidity
Max. 90 % (no condensation)
Colour
RAL 9003
Mounting
Surface, wall-mounted
Dimensions (W x H x D)
Enclosure: 200 x 153 x 47 mm
PCB: 150 x 82 x 20 mm
Weight
0.34 kg
Housing material
ABS
Housing
Plastic enclosure
Housing protection / IP
rating
IP30
Standards
EN50131-3:2009 (Grade 3, Class II)
Deutsch
– Anweisungen
WARNUNG
Lesen Sie vor der Installation und Verwendung dieses Geräts
die Sicherheitshinweise.
Das Gerät darf nur an einer Stromversorgung angeschlossen werden,
welche der Norm EN 60950-1 / Kapitel 2.5 (
„begrenzte Stromquelle“)
entsprechen.
Beim Austauschen oder Installieren eines SPCW130 im SPC-System
müssen während der Handhabung von Anschlüssen, Drähten, Klemmen
und Platinen alle erforderlichen Antistatik-Maßnahmen getroffen werden.
EG-Konformitätserklärung
Hiermit erklärt Vanderbilt International (IRL) Ltd, dass dieser Funkgerätetyp den
Anforderungen aller relevanten EU-Richtlinien für die CE-Kennzeichnung
entspricht. Ab dem 20.04.2016 entspricht er der Richtlinie 2014/30/EU (Richtlinie
über elektromagnetische Verträglichkeit) und der Richtlinie 2014/35/EU
(Niederspannungsrichtlinie). Ab dem 13.06.2016 entspricht er außerdem der
Richtlinie 2014/53/EU (Richtlinie über Funkanlagen).
Der vollständige Text der EU-Konformitätserklärung steht unter
http://pcd.vanderbiltindustries.com/doc/SPC
SPCW130
– Einführung
Das SPCW130 stellt eine Schnittstelle für 868-MHz-Funkmelder zur Verfügung.
Das SPCW130 besteht aus folgenden Komponenten, die in Abb. 1 dargestellt
sind:
Das Erweiterungsmodul sollte mindestens 30 Sekunden lang mit Strom
versorgt werden, bevor irgendwelche Operationen ausgeführt werden.
1.
Sabotageschalter auf der Frontplatte
— Das Erweiterungsmodul hat einen
Sabotageschalter mit Feder. Beim Schließen des Deckels schließt die Feder
den Schalter.
2.
Tamper Bypass [J1]
— Die Jumper-Einstellung legt den Betrieb des
Sabotagealarms fest. Der Sabotagebetrieb kann durch Stecken von Jumper J1
umgangen werden.
3.
Summer
— Der Summer wird aktiviert, um das Erweiterungsmodul zu
lokalisieren (siehe Konfigurationshandbuch).
4.
Funkmodul
— Das Modul stellt eine Schnittstelle für 868-MHz-Geräte zur
Verfügung.
Beachten Sie, dass Sie nur drahtlose Intrunet-Geräte an diesem
Funkmodul anmelden können.
5.
LED
— Leuchtet, wenn Funktelegramme empfangen werden. Die LED zeigt
den Empfang aller Funktelegramme an. Sie zeigt auch den Empfang von
ungültigen Funktelegrammen an.
6.
X-BUS-Status-LED
— Die LED zeigt den Status des X-BUS an, wenn sich das
System wie unten dargestellt im Konfigurationsmodus befindet:
