VAM KOA Owner'S Manual Download Page 7

HOW TO INSTALL THE FAN

16
Terminal Block located on the hanger bracket.

17. 

Connections:

    - 

Brown 

fan wire is connected to the Live 

      supply.
    - 

Blue 

fan wire is connected to the Neutral 

      supply.
    - 

Green/yellow 

fan wire is connected to the 

      Earth supply.

18. Connect the Fan wires from the downrod to
 the 3P plug from the Receiver.

19. Connect the 2P plug from Receiver to the 
3P plug from the terminal block.
(Figure 9)
 

. Connect 240V main power (dwelling) to the

Figure 9

Brown
Blue

M

o

to

r V - P

u

rp

le

M

o

to

r W - B

ro

w

n

To Motor V - Purple

To Motor U - Red

To Motor W - Brown

220-240 Vac SUPPLY
(User Supplied)

N

L

AC IN - N

AC IN - L

Green/yellow

1P plug

3P plug

EARTH

 

Green

/

Yellow

Terminal

 

Block

on

 

Bracket

M

o

to

r U - R

e

d

2P plug

5

20. Install the receiver into the hanger bracket,
above the hanger ball. 
(Figure 10)

Canopy

Screw

Figure 11

Canopy

Ring

Canopy

Coupling Cover

21. Slide the canopy up to the mounting bracket
and place the key hole slots on canopy over 
the two screws on the mounting bracket.

22. Rotate the canopy until the screws head locks
in place.

23. Re-tighten the 2 screws and reinstall the other
2 screws.

24. Install the canopy ring by pushing it up to the 
canopy. 
(Figure 11)

Figure 10

Before commencing installation, turn off electricity supply 
at the main power box or disconnect power by removing 
fuse or turning off circuit breaker. 

WARNING

Summary of Contents for KOA













Reviews: